We are using the SSID tunnelling and L3 roaming to MX250 as the wireless concentrator. I want to move this SSID tunneling and L3 roaming to the vMX on AWS. Does vMX support this setup and how to configure it?Thank you.
Forum Posts
I have few APs joined the C9800 WLC. The WLC is running on firmware version 17.9.3. Regulatory domain is set as MX for Mexico. But the operational status does not come up.
Resolved! converting C9130AXI into EWC
I am currently trying to convert a C9130AXI into EWC I have done a factory reset using 30 sec push of factory reset button see belowWait for the button to be released ....Button pressed for 36 secondsSetting env for full reset..Writing to Nand... do...
We use scanners in our company that can be wireless, our Meraki wireless is configured with Nat Mode"Clients receive IP addresses in an isolated 10.0.0.0/8 network. Clients cannot communicate with each other, but they may communicate with devices on ...
Hi community, I have a pair of WLC 9800 in HA mode. The management interface labelled SP on the standby WLC is down, lights out even though it is configured the same as the SP port on the primary (different IP). Is this normal behaviour?
I am using 9800 wireless controller with C9120AXI wireless AP. When I connect to wireless SSID from a device via EAP-TLS, EAP-PEAP, it will connect successfully with TLS 1.2 protocol. When I connect to wireless SSID from a device via EAP-FAST, it alw...
Hi allI have an issue where when some users are roaming from 1 side of the building to the next they drop off the network and have to forget and reauthenticate. I didn't set this controller up but I can see Fast transition is adaptive enabled. So I s...
I am deploying the Cisco 9136 AP for 6E in our new office building at high density. What has been the recommended power on this AP in office settings? I typically deploy from 8dBm to 14dBm but curious what others have done with this new AP over 6Ghz
Due to the license issue in the c9800-cl model, the number of joined apps was limited, so we created a rum file with air gap and imported the ACK.rum file by referring to the link below. https://www.cisco.com/c/en/us/support/docs/wireless/catalyst-98...
Hi We are going to purchase Access points C9115AXI-I and C9115AXI-EWC-I . Both are same prices But C9115AXI-EWC-I is announced by Cisco to be end of sale end of this month. So we can purchase only C9115AXI-I with the DNA essential license I need to c...
If connectivity between WLC and AP goes down for sometime, will clients connected to AP's face network disruption? or there is any grace period that client's rest of use(browsing, access) will work.
I have to deploy APs to branches using flexconnect. Do i need to preconfigure the APs on my local controller then ship them out or can i just load in the MAC along with the tags i want on the AP ship it out and then itll grab everything it needs? eve...
Hi. We have 3 new 2802I that we can't get to work. We're using a 3750 switch to power the other 2702 which works fine with our 2500series controller (version 8.3.112.0). Since the 3750 can't provide enough power for the 2802 we bought a couple of D-l...
Hello,We have MR36 in our office.We currently have latency issue everyday, rebooting the AP solve it for short period of time.Workstations on LAN have no issue.Anyone have a working solution for same.Thanks
Hello everyone. I have a conference room and it is equipped with a C9130AXI-S. I have searched for the installation instructions so that it can broadcast wifi in my conference room but I can't find it. So I hope everyone can help me with the installa...
