Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Folks,On a Cisco 5508 controller how can I find out which clients are connected using "n" speeds only? I see logs that there are connection using "802.11b/n", but how does this help me?Also on the new Wireless AP's i.e. the 3602 and the 3702 AP's. Wh...
I have a AIR-SAP1602E-A-K9. My question is do I have to install an antenna on all three antenna connections?
Here's a weird one. I have 3 industrial machines with the same hard coded IP address, 10.255.10.10/24. I need 3 different laptops to communicate with it's respective machine through a 2504 WLC. On the switch it's not a problem, I configure VLAN10, VL...
Is there a best practice for grouping lightweight access points in one vlan or allowing them to be spread across several ??
Hi MR.Rene,I have a Topology scenario of our upcoming project which we are planning to execute. This will be a replacement of our old setup of ISDN and PSTN lines.We have taken MPLS Private Line from ISP provider which will be maintained by ISP her...
Hi All,I have a Topology scenario of our upcoming project which we are planning to execute it for the existing project. This will be a replacement of our old setup of ISDN and PSTN lines.We have taken MPLS Private Line from ISP provider which will be...
Hello, My customer have Ap's AIR-AP1042N-T-K9 models, and need to convert LWAP to use them on a controller, but needs an official Cisco documentation to perform. I found many posts with the statement that this is possible, but no official document fr...
Dear Support,we are using two WLC 5508 software ver.7.4.100 with first 50AP license and in the next day we add 50AP license again to the primary WLC. when we activate HA base in the following guiden http://www.cisco.com/c/en/us/td/docs/wireless/cont...
we have network with nexus 7009 core and a module ML-148GS-11L we are deploying cisco wireless in the netowrk. wlc 2504 and AP 2602Iwlc 2504 connect direct to ML-148GS-11L (trunk)interface Ethernet5/35 switchport switchport mode trunk no shutdow...
We're having a problem with interference in the B/G range due to the large number of access points owned by other companies in a fairly small area. The various laptops keep deauthenticating, which is causing problems with applications. I'd like to co...
Hello This is a strange issue.Network connection paramaters:-Remote site has 50/10 cable link (no QoS). Cable company has verified connections/signal etc.. = good-Wireless AP is cisco AIR-CAP3602I-A-K9 which connects back to a WISM (WS-SVC-WISM2-K...
Hi,I have one 5508 WLC & by mistake by default it's comes with the Russian ios code. Now I am trying to change the ios 7.6.110.0 but I am unable to reimage it pls help me out for this. What do I need to do for that. Regards,Rahul Wankhade
What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class IdenfierThese items are listed with 1600 series AP but I'm unable to understand what are these things & the use of them
hi, can any one help me to configure AIR-CAP1602E-N-K9 as standalone acess point. its a new one with default setting as per my knowledege its a controller based access point so pls help how to convert into standalone access point and which image is c...
Hello I wanted to ask if I have to create a subinterface Dot11Radio0.610 since I cannot change the VLAN on the Switch it connects to is it fine if I create and assign a bridge group 61 like this or they need to match and such a configuration can pote...
