Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello,I have a problem configuring ClientLink on a FlexConnect local switching AP (3602i), the problem is that I can not see the clients that are using the ClientLink feature when entering the show interface dot11radio 1 lbf rbf command, the AP shows...
Resolved! ASCOM wifi phone problems
Hello;I have a problem with wireless phones are brand ASCOM. Are supported by Cisco. The problem is that, without moving your site, you lose your coverage and 3 seconds back. The configuration of the WLC is recommended by ASCOM. The wifi network is c...
Resolved! WLC Syslogging
I have a syslog question. We do not send any logs from our controllers to any other system. What is the best software to capture logging from the controllers. We have ciscoworks but we do not have our controllers added to ciscoworks. I am a little bu...
We are forced to rush a installation of a WLC 5508 various reasons in a testing lab. I eventually want to configure RADIUS and such but cannot do it at this immediate time. What I would like to do is impliment straight forward MAC filtering. The prob...
Hi all,the data sheets provide the number of max supported APs on different controller platforms.However in practise typically services can get affected before reaching this threshold.for obvious reasons no vendor will come out and state the practic...
When adding a new MAC filter on WLC .there are some fields i dont fully understand.1. Profile Name2. Interface Name 3. IP addressif i understand correctly to add MAC filtering to specific WLAN , i need to enable thatin the WLANs security tab.so wher...
Good morning! About this topic I would like to have some clarifications: in a wireless controller the default is WMM for the AP managed. So what does it mean that? Could APs use a minimum and a maxim time wait of transmission? As explained in the li...
I have an Aironet 1040 access device, no controller. I have an LDAP server with radius in front to allow for username and password authentication(using MS CHAPv2) with mandatory WEP and PEAP.I was wondering what the strongest security option is that ...
Resolved! Vertical mount 3602e antenna position
When mounting 3602E vertical should all the dual antenna point in one direction (ie all up, all down or 2 up and 2 down?) Thanks Steve
Hi, When I tried to download software for WLC44xx, I noticed both mesh and standard software releases. Do I need to keep seperate controller for mesh APs?.WLC with standard sw can not handle mesh APs? thanks,Ramesh
Resolved! Question Regarding AP Image Pre-download
I'll get straight to the point on this one. I have 84 LAP1242AG access points and a 5508 WLC. Currently, the WLC has version 7.4.100.0 set as the primary image with version 7.0.116.0 as the active/default image. Presently, all APs are running vers...
Hi,I am using AIR-LAP 1041N-A-K9 wireless Accesspoint it was controlled by using the Air-CT2504-k9 Wireless controller.When I tried to connect the access point using Windows 8 machine it was not able to connect, Is there any one who faced the same is...
Experts,I got a customer's reqeust about 1262E /w special Ant which is high-gain than traditional Ant (dipole 2-3dB).They think this would improve of its coverage area.But, once upon the time, I used to test 1252E with high-gain directional Ant mysel...
HiJust got a replacement MSE as the other was DOA.Upgraded to 7.0.230 to match WCS. The Appliance starts, but when starting the MSE Platform,Starting Datase.....Donesudo: unable to execute /opt/mse/framework/bin/framework.sh: Permission denied.MSE P...
we have two controllers model 2100 and 2500 the first controller model 2100 have the following system information Product Version.................................. 6.0.196.0RTOS Version..................................... 6.0.196.0Bootloader Versio...
