Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi friends,I have the WLC 5508 release 6.0 and AP clients LAP1142, and is enabled frequency 2.4 ghz only.How I could enable frequency 5 ghz in the WLC?Best Regards,Ale
hi I am trying to add 0.0.0.0/0 as SNMP address and netmask and i am getting an error saying the netmask is invalid.is there a different way to set this?
I'm trying to setup 2 units of 5760 wlc with HA for @100units AP3260I.Questions on HA:-1. Can the new 5760 wlc do HA-SSO ?2. Another option documented is AP-SSOI managed to configure the APs for primary and secondary controller mode but during the sw...
Hi people,I have a WAP4410N-E V02 with software version 2.0.6.1 buyed 2 months ago that restarts every 24/30 hours (about).The device is univocal in the network and is configured as an access point without dhcp server. I activated remote syslog and s...
Hi together,a customer has lost some Access Points to another WLC with 7.2 and then they come back after 15 minutes to the origin WLC with 7.5Attached the messagesMFP Protection is configured as optional152 Wed Nov 27 05:33:26 2013 MFP Anomaly Detec...
Hi All, new to the MSE world during the install of my new MSE virtual 7.0 it asks to change the root password...however the password requirement would not let me change the password and thus fell back to the default. How can I change the root passwor...
I have 1130 on each floor and planning to add 1141 AP for coverage / redendency. Does it matter if I mix and match on the models? I am using Radius.Should I "deploy" the identical model on the same floor?
Hi,i'm reading the doc at http://www.cisco.com/en/US/customer/docs/net_mgmt/prime/infrastructure/2.0/quickstart/guide/cpi_qsg.html#wp46865and I'm searching for the CPU requirement for a Standard installation. From table 2 in this document, I will nee...
Dears,We have Cisco Prime NCS Ver.2.0 running on plad. Since yesterday the alarm give us severity major message (Message: CPU: 85 crossed down threshold: 90).Please advice what this problem and how to solve it.Thanks,
HelloI have 3 new Cisco AIR-SAP1602I-E-K9 for a large 2 floor halls. Max Users: 50. What could be the best practice tools to calculate the signal coverage + quality + speed when installing the access points through the halls ?Thanks for the answer...
I am using Cisco 2500 series WLC with 2 access point and i want to run Internet which is PPPOE dial-up Connection, i need refference Configureation for start my Internet,
Hello,I've been observing with multiple access points and multiple wireless clients that RSSI signal received varies even 10dBm depending on whether the device is associated with the access point or just is listening to. When is associated is the max...
I need to use 14Dbi patch antennas (like AIR-ANT5114P-N I use to have on AP1522) on AP 1552E. Is it possible?
We have 4 of these phones connecting to 2600i AP's on a WLC. They can sit idle for hours, but when you make a call, it will work, then at random, just drop off and reboot. I also noticed that response times to all 4 phones will be good, around 30-40...
Hi, We are using 25 cisco AIR-LAP1042N-T-K9 AP´s with WLC AIR-CT5508-K9 (7.0.116.0) at our distribution center. The issue is that the mororola MC3190 (windows CE 6.0) handheld works fine for a while and stops when doing the roaming. It is not all t...
