Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I recently installed additional licenses on my 2 WLC 5508s. Then I installed NCS on a virtual appliance. Installed the NCS license, added the controllers, refreshed configs, created templates, etc. However, when I go to look at the License Center, I ...
I have a lot of cisco 1231G APs in our school district. Recently they were having issues with the signals in some areas. Now when we try to test to see if there is a signal it keeps fading in and out. Sometimes there is no signal there. Our APs a...
Lately, I've been hearing reports from a couple of techs that profiles configured in the ADU will mysteriously disappear and the default profile (which was deleted) reappears. Has anybody else seen anything similar? If you have, have you figured ou...
Could someone inform me if the AIR-AP1242AG-E-K9 is compatible with AIR-ANT5160V-R?Both of them use RP-TNC connectors but in PDF says for Cisco Aironet 1250 meanwhile for some other antennas it says "Best suited for use on the Cisco Aironet 1250 Seri...
Hello friends,I have few Cisco 1522 Outdoor APs in a Controller based environment.we want to implement 802.1x (MAB) for these Access Points.Problem is:When I type the "show mac address-table interface gx/x/x" command on the switchport where the AP is...
I have two AIR-AP350 SERIES AP's. I am receiveing wifi from my friends house a mile away across a valley with clear line of sight. I think there is a problem with one of these units because when doing a link test one unit shows 14% signal strength ...
I'm having problems getting HP iPaqs connected to our wireless network. The iPaqs DO initially authenticate and access the WLAN but when they are not being used for a while or they are restarted they will not reconnect.The error message on the contro...
Hi All,I'm trying to put together a Guest WLAN setup and want to know the best approach.If I use ISE for Guest portal/access control do I still have the standard setup of Anchor WLCs in DMZ for the guest WLANs?Or does the ISE tell the internal WLC's ...
Hey all,i have a problem with our new 5508 wireless controller (7.0.116.0).Port 1 is the system default "management" (Port 2 is backup). Dynamic AP Management is disabled.Port 3 is a new dynamic interface "ap-manager 2" with Dynamic AP Management ena...
Hi,Has anyone successfully deployed a 4 channel (1, 5, 9, 13) none-overlapping plan in the UK?Cheers,Jason
I am using guest solution with two WLCs , one inside and one as anchor in DMZ.we have also NAC guest server to authenticate the guest users. inside WLC is 5508 and had been updated to latest version 7.2.103.0 last thursday.now we facing problem wi...
We are in the process of evaluating Cisco wireless controllers and AP. We have 3602 APs and 2504 controllers right now. We have mutliple branch offices connected to the main office through layer 3 and they all have different vtp domains and vlans. I ...
Resolved! Bridge Mode Support on AP1041N
Hi,I'm trying to get confirmation on whether you can have workgroup bridge mode on the 1040 series model. The 1041N has the same IOS as the 1141/1241 and it has the settings are there, but I read somewhere on the cisco site that workgroup bridge is o...
We have recently converted 1 Cisco Lightweight AP 1041 to Autonomous mode for site-survey purposes. We now want to convert it back to lightweight mode. Is it possible?
We have two 5508 WLCs. In addition to our 3 current SSIDs, We added a new test SSID which is directed to a NAC device for 802.1x authentication. The configuration selected only WPA2 Policy, AES and 802.x for AUth Key Mgmt. The problem is that the new...
