Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
We have about 100 devices that need to be added to our mac filter. Before now, we just did one or two at a time. This is the first time we have such a bulk order to do at once. I was taking a look at the sample .csv format and had a question before I...
Hello,I have a WLC2500 which controls some 1310 lightweight APs.I've loaded an autonomous IOS on one of the 1310 APs, and configure it as repeater.Repeater is successfully associated with its parent lightweight controlled AP, and r...
Has anyone setup a 1600/2600 as a wireless mesh/bridge with the dual band antennas? I'm curious to see how well they work with the dual band antennas and how well the 5Ghz backhaul works in conjunction to the 2.4Ghz client side.
Does anyone see this error on 5508 controller with 3600i APs? WLC is running v7.3.101.0*apfOrphanSocketTask: Apr 04 09:44:41.444: #IPV6-3-INVALID_ADDR_ORPHAN: ipv6_net.c:715 Invalid ipv6 address ::, failed to do data gleaning.Thanks
Hello,We are wanting to expand our wireless network and we currently have a 5508 controller with 150 AP's. We will be adding another 100 AP's soon, and we were thinking of possibly adding an HA controller or a second controller. Current AP's are al...
Hello everyoneim new here. but i have a question. its about the Cisco Prime ncs.i have installed the Cisco Prime with a ova file on a VM-ware server.i have configured the cisco prime with the setup at the beginning. but the problem is that i can't ge...
Hi,I would need assitance on explaining the heat map in Cisco Prime. Some AP's signal are shown as red (-35-45 dbm) , but some AP's are shown as yellow (-55-65 dbm).Utilization, power, comparing the AP which has excellent red signal and yellow/green...
Hi all,I've seen this problem more than once..Today I Installed AP-adder Licences and so hat to reload the controller (7.4.100).because of the AP-SSO Cluster, I hat to wait a few minutes and than could failback to the Primary controller.All seemed to...
Where are the AP groups in PI 1.3 ?The documentation in PI 1.3 states Step 1 Choose Configure > Controller Template Launch Pad. Step 2 Click AP Groups or choose WLAN > AP Groups from the left sidebar menu.AP groups in the controller itself shows the ...
Dear All,I am trying for the migration from WCS to NCS. I need some help for the below steps been taken by me is correct or not...1) From WCS - Export XML file2) From CISCO Portal (Licensing)- Get newly generated license3) Install NCS 4) Add the new ...
Hi,I have a WLC5508 with around 70 AP's (LAP1042N) connecting over an MPLS WAN network.WLC and AP's are running 7.4.100From time to time I have an AP which disassociates from the WLC with the logging beneath.Can anybody tell me if this is a problem w...
Hello,We have installed 2 new WiSM-2 in HA with software version 7.3. We have also upgrade NCS 1.1 to PI 1.2.After adding the primairy WiSM-2 in PI we can manage the WiSM-2 for a short time from PI. But after a few minutes we lost the connection to t...
Hi,I´m wondering if there is a possibility to mark wlan-traffic network upstream (meaning traffic leaving a LWAP towards the WLC) with a dscp value even if the client doesn´t send any WMM information. thanks fpr your help
Hello,We have currently a WLC 5508 using 8 ports bundled into an etherchannel.We would like to remove one physical from this etherchannel and use it for providing an access to Internet only,Is it possible to create an virtual interface on the WLC tha...
Hello Community,I am having a very peculiar issue wherein an 1142 WAP is randomly disassociating and powering down due to what the Trap log is calling a "Watchdog Timer Reset." The only way I can get it back up is to power cycle the AP. Currently the...
