Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Dear all.My customer returned me a malfunctioning Cisco 1242AG access point. In the end of initialization process I see all three LEDs are solid red. I revealed that this due to the corrupted IOS image. I reflashed the AP via TFTP server to firmware ...
Can the AIR-WLC526-K9 be used for any other access points besides the AIR-LAP521G-A-K9 access points? Does the 526 controller use the LWAPP protocol?
Hi @ll,I've just got a new AP 1250 series, and I was trying to configure the Radio for the 2.4Ghz spectrum using the interface dot11radio 0 and I've just noticed that this controller is not present so I cannot configure it so I wonder is it could be ...
Hi All,Been trying to resolve an issue with WCS 5.2.130 (linux) - it is running really slowly so I moved it from a machine that was a little below spec to a VM, still really slow.... The question;I discovered under background tasks Client Statistics ...
Resolved! Designing a wireless location
I believe that I understand the difference between 2.4 and 5 GHZ when it comes to designing coverage to a location. I would like to know if anyone ever setup a conference room with 25 laptop’s where there is a greater concentration of device in a sma...
Hello all, With the new release of the Cisco AnyConnect(ver 2.5.4038) for iOS and the new release of iPhone Configuration Utility(ver 3.4), Do any of you know how to create a mobile config file that will allow for automatic certificate select...
I have to make a migration from a controller to oher.We have now in production a WLC 4406 with 90 AP in local mode and HREAP mode, and we have to change the WLC to other new model 5508.Do somebody know which one could be the best method to do that???...
Does anyone know what the "Provision Failure: MEDIATION-5, Lrad! errors are in WCS? I get this when pushing an AP template to six new 3502i series access points. The error reads like this:*** Apply Result for AP 'NameOfAPhere(C0:FF:EE:C0:F:EE)' ***...
Hi All,Just have a basic querry, What is the default mode of 1142 AP. When it's shipped from Cisco, Does it works as LAP or it can be used as a Autonomous ?Also, incase we just get it shipped from Cisco, does it have any default IP address that we ca...
Hi everybody, i am expecting an issue with my WLC 5508 with IOS 7.0.116.0. The traffic related with controler managment ( GUI and telnet access and RADIUS) is passing trough service-port.The managment inteface is connected to catalist 6513 with folo...
Is the switchport tracing feature in WCS compitable with non-cisco switches?
Resolved! 1041N APs not joining 2100 WLC
Hopefully this will be an easy solution for some of you.I have two LAP1041N APs I am trying to setup on a new 2100 WLC (7.0.116.0). THe APs will blink green fast; then go to a green, red, blue cycle for a min or so; then back to blinking green fast....
Hi,Currently we are running Cisco wireless AP's in an LWAPP setting with Cisco WISM. Wireless authentication for network access is linked to our Active Directory.What we are noticing is that a large number of users are connecting to the wireless usin...
Hi, As according to the cisco config example. (http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008067489f.shtml),it says:If clients are in Webauth_Reqd state, no matter if they are active or idle, the clients will ...
Resolved! 1260 AP question
have another question regarding the 1260s. If our one, 2500 controller with 1260 APs, running CAPWAPP image goes down, will those APs look for another contoller even if there are no CAPWAPP controllers to be found(only LWAPP)? And if it finds one, wi...
