Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I have WLC 5508I am using web authenticationIf I dont use proxy server in my internet explorer, no problem, web auth. page comes ...butIf I use proxy web authentication page does not comeProxy server is located on DMZ with real IP addressPlease help
Hi friend,I have to bridge 1400 series which in the virtual interface has a CRC errors, i don´t the reason, maybe the link (point-point bridge) is misaligned.could someone help me.Thank,Marco.
Hi folks, First time out here on the Cisco discussion board and seeking a little help... My company currently has a WLC-4402-12-K9 in house and is up and running without issue (except that we're out of WAP licenses).With that said, I finally got mana...
I'm hoping someone can help me with this as I just pulled the AP out of the box and haven't received support contracts yet. I connected the AP to the LAN and added it to my 4402 controller (version 5.2.178.0) with no problems. Once I set it the mod...
Hi,Iam facing the issue with Cisco LAP getting registered with WLC 2112. Running version of WLC is 7.0.116.0. LAP is rebooting repeatedly.sh logSyslog logging: enabled (1 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns...
I there.I have a problem with an AIR-AP1242AG-EK9 access point. I start the access point and after a short while it reboots by itself, this keeps appening and the time that it takes to reboot isn´t always the same. I´ve tried different IOS versions a...
Resolved! Ap 1131AG can't access device
Hi alli am new here and this is my first post - i am sorry for mistakes.I have several AP's of 1131 AG used in autonomous mode. Resently one of them stops responding:i was not able to access web management or ping its NIC.I've tried with reseting dev...
Hi,we're a small bussiness with about 20 WiFi Clients in the process of deploying WiFi VoIP on an fragmented office area of about 300m² on two levels. By doing a simple site survey of our current WiFi installation I know that we will need multiple AP...
What wireless access point should I use with my PAP2T that is being used as an ABN for NextAlarm with my home alarm system? I have been told to stay away from the WBP54G and understand it has been discontinued, although it is still listed for sale o...
Hi All, I have cisco wireless client which is not in domain, I am trying to associate to a WLAN with 802.1x. ACS is configured for authentication and AD is used as the backend database. When I use a local username/password the client can associate,...
I am trying to configure port 8 on the WLC 5508 to a dsl line that connects to a linksys switch. This is seperate from primary port which is configured as LAG and has the rest of the vlans. I am not sure how best to achieve this.
I have been tasked with finding available options for integrating an SMS gateway into our UCM environment. Goggle searches find 1000s of hits without any real guidance. So I will post the question here.Are there SMS Gateway solutions that you are usi...
I have a problem where clients cannot roam between Cisco 1231g-e-k9 and recently installed \cisco 1242g-e-k9 access points.. On looking at the CDP option on the 1231 and 1242 access points they are all aware of each other. However if I use the Netw...
Hi @ all,have anybody an funktional configuration with HP ProCurve Switches to use the LAG (LACP) mode in conjunction with the WLC 4402 or 5508 with Software version 7.0.112.0? The HP Switches in the enviroment have the last Firmware version installe...
I am trying to connect a WLC 4402 5.0.148.0 mode with an HP 2800 switch. The switch is configured thunk mode with LACP protocol. The WLC in LAG mode uses the protocol LACP? How can configure them switch HP?Thanks.Mirko Severi.
