Hello,What we want to achieve is the following construction:Current setup:Organization (ITASS) > Network (Kremer Zand en Grind)Currently the network 'Kremer Zand en Grind' is configured under the organization ITASS. We want to split all our customers...
Forum Posts
We have a WLC 5520 running version 8.10.190 connect to various access points, model 2802. Our WLC has the correct time and date and taking into account BST but our access points have the correct date but is using GMT, meaning our access points have ...
Hello,I have upgraded my C9800 WLC from 17.6.5 to 17.9.4a successfully. However now I have RADIUS interim update issue.I have external captive portal - RADIUS SSID configuration which was working fine before. Also RADIUS accounting and interim update...
I have a question….I have a Catalyst 9105AXI-B and a 9115AXI-B that I need the Access Point Manufacture Image however when I try to download the Image it says I need a service Contract. Do you know what the price would be for that?
Hi, We have a customer network with 20 2802 series APs operating in FlexConnect mode on a 3504 WLC running SW 8.10.156.0 However, only 8 of them are transmitting on their 2.4Ghz interfaces even though the the interfaces are up and the SSIDs are confi...
Resolved! 9166I and 9300 Switches
Trying to get some 9166I access points online today. Ceiling mounted through Cat6E patch cords (x 2 ) and structured cabling. They power on but don't do anything else (amber LED which never reaches "rainbowing"). If I remove them and patch them strai...
Hi,I have an ISP wireless router which coverage isn't enough for the whole house and I'd like to extend the wifi to reach everywhere in the house. I have some older autonomous AP that can be setup as a repeater to extend the coverage, but unfortunate...
Hi, I'm getting a surplus C1111-4PWE .Can the embedded WiFi AP be used independently, or will it only work when connected to or controlled by a separate Cisco controller?
I am currently in a POC with a Meraki MR36. When connecting the AP to the network, it is not getting an IP address.Does the port on the switch have to be configured as a trunk port?Thank youDon
Hello,i need your help , on our AP meraki i have this configuration , and i want to know how i can set the best config on my caseon what I have to base myself to design this config for 5ghz and 2.4ghz?Radio transmit power range (dBm)?Minimum bitrate?
Hi guys!! is possible to allo webex audio calls between clients connected to the same SSID, with "Layer 2 LAN isolation" enabled?Thanks for all!!Marcos
Resolved! AIR-AP1852E-B-K9 - L2 Error Detected
Here is the complete boot capture: If I interrupt the boot, I can tftpboot at the (RNAQ-C7) # prompt a new ap1g4 file as part.bin to the device with no change. #====================== Connected 6:07 PM 10/18/2019 =========================# U-Boot 2...
Resolved! Cisco 1832i L2 Error Detected!
Hey guys!I have 6 APs 1832i and a WLC both of them version 8.2.151.0. One of these AP stopped working a days ago blinking red,amber and green, I rebooted, changed cables, etc, but nothing worked. I just updated to V 8.10.151.0 but in the booting proc...
Hi Everyone, I am struggling with following issue while using Guest internet followed with Sponsored guest Login - Splash Page authentication.In general The sponsor login page relies on the name and email address entered then should redirect to enter...
Hi,Trying to set up a brand new 9130-EWC as a replacement for my Mobility Express network in my home. I power it up, launch the Cisco Catalyst Wireless App, scan the code, and I'm getting the message "Connection to SSID 'CiscoAirProvision-0890' faile...
