Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Dear all I start learning about Mobile IP( read the RFC 3344) and some related RFC documents. Now i have a concern question, Hope that you clear a canal of obstruction because it makes me getting mad.As i know about Mobile IP like this:+The Foreign ...
I have a customer running WCS on a windows server plataform (physical server), and want to move to cisco prime (UCS 210), however I can not find a migration guide in order to keep the backup, once the cisco prime will be virtualized in another server...
Hi everybody,we have a lot of WLANs and AP groups on two WiSM2. Each AP belongs to some non-default AP group. Now I would like to change default WLAN to interface mapping. But change of WLAN to interface mapping on the WLAN configuration page changes...
I have 8 no. AIR-LAP1131AG-A-K9 and WLC 2112 Wireless LAN Controller,i configured the device and its working at deffent SSIDs but when i am trying to enable same SSID on all LAP it shows "AP on dupplicate SSID found and Layer 2 security found".
Hello! Please, help me to sort my problem out.We have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought ...
Hi,is anyone experiencing frequent disconnection on CleanAir APs. installed 2 cleanair aps, aironet 1550 in bridge configuration. in the vicinity there co-exist ubiquiti brand APs around 3 units. i have done frequency survey and configured channeling...
Hello,we do have a site where we need to deploy AIR-LAP1142N-E-K9 and AIR-LAP1242G-E-K9 APs. We have two AIR-CT5508-K9 controllers with SW version 6.0.188.0.AIR-LAP1142N-E-K9s work okay, as expected, we do not have any problems with ...
Hello Guys,I got a project where I have to provide NATTED addresses to cutomers for the internal servers and I found out that the outside address range /27 already in use. We are using 5510 with ver 8.1. We cant use PAT here.Any other option to acomp...
Folks, I have a need to troubleshoot/test 802.11k, 802.11u, and 802.11r messaging. Does anyone know if AirPcap Nx + Wireshark will capture and properly decode these 802.11 amendments:802.11k802.11r802.11uI have looked in Wireshark forums and seen ref...
I have a rather basic questionWe have obtained a WLC4136-K9 controller and a AIR-LAP1252G-A-K9 access point (with power injector - AIR-PWRINJ4). I'm having a heck of a time trying to get the AP seen by the controller and also am having trouble with t...
HelloI am getting a hard time in order to understand the real difference between the two types of context aware licenses for the MSE:1 . AIR-CAS-1KC-K9 - Context Aware License For 1K Clients and Tags (RSSI based) 2. AIR-CAS-1KT-K9 - Context Aware L...
I got new cisco aironet 1262n Dual band Access-point running IOS version 12.4(23c)JA .my question is does this access-point support 40 MHz channel width on the 2.4 Band on any IOS version as the command "Channel width" under interface dot11radio 0 al...
Folks, I am new to ACS5.2, I am setting up a wirless network and want to write a policy where desktops will go in a specific vlan and laptops would go in a specific vlan. I am reading documentation on ACS 5.2 and it does talk about device t...
Currently we have WLC 4402 and wide range of AP. We use WAP2 with EAP-PEAP-MSCHAP for the WLAN security setup. We use MS IAS as radius server.Recently, we want to find a way to control what type of wireless devices that can join to our WLAN. One id...
I have a cisco 4402 wireless lan controler, I have a campbell scientific CR3000 device with and ethernet module. When I add the device with an ethernet cable directly to the network I can see the static IP for the device and can ping it. But when i ...
