Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi Is it better to use dedicated monitor-mode wIPS access points or shared-user-serving, local-mode access points with clean ir and WIPS this is possible?
Our wireless infrastructure is comprised of about 50 cisco 1131 LWAPs and two controllers... a 4402, and a 5508.Our primary SSID is published, WPA + WPA2, Auth(PSK)For the most part, we have no issues whatsoever with any of our workstations connectin...
I have just upgraded one of our 4400 to 7.0.98.0. Most of the AP re-registered with out issues. I have two AIR-LAP1142N-E-K9 on a remote site that will not re-register.I have pointed them to another 2125 WLC ( 7.0.9...
Resolved! Adding Controller to WCS
I currently have a 4400 controller and I am looking at implementing WCS. Will adding the controller to WCS change the controller settings? I don't want to take down my production network.
I have an XP machine that can not log onto a 2003 domain with the a certain name. I have narrowed it down to the name and on wireless. If i put this on the wire it works fine and if i change the name it works fine on wireless. Due to our naming conve...
Hello,I am constantly getting error on UC520W Wifi from last Night, I am not getting with this error,Can anyone help me , what is the cause of this error, or is there any issue on UC520,Please suggest & help me .858: %DOT11-6-DISASSOC: Interface Dot1...
How do I know which hardware I have? I can't find a HW versio anyware on the appliance or in WLSE itself. I am guessing 1105 beacuse I saw a 1105 as part of the path in the repository.
Resolved! Help with Cisco 1242ag Password reset
I just purchased a used 1242AG which is running Version 12.4(13d)JA.I tried the mode button on power on holding for 2-3 seconds, but nothing happens and Cisco/Cisco login does not work. I have figured out if I hold the mode button in for 30 seconds ...
There's a new IOS release (12.4.25d-JA) with support for the 1260 access point in autonomous mode. However, I haven't been able to find a part number for purchasing this combination. It appears to me that I would need to do the following:Purchase a l...
HiI have a CDMA ISP, and I ned to connect my little network to the ISP, I found that Cisco has this kind of module for Cisco 881g seriesPCEX-3G-CDMA-VPCEX-3G-CDMA-SPCEX-3G-CDMA-BWhen I ask my ISP to help me in my choice, the said:'' This kind of modu...
hi,i have a HWIC-AP-AG-A running in 2801 router.RTR01(config-if)#do sho run int Dot11Radio0/1/0Building configuration...Current configuration : 367 bytes!interface Dot11Radio0/1/0 no ip address no dot11 extension aironet ! encryption vlan 30 mode ci...
Hi,We have a customer with ACS 4.2 Appliances who currently uses the Layer 3 web-redirect guest function to authenticate users against AD via ACS and LDAP to the AD, its a mixture of un-managed Windows, Mac & linux clients.They want to move to an 802...
Resolved! Some newbie Aironet Q's
Hi there,I've been trying to fix some problems with a stadium aironet setup and was hoping someone could help me with some Q's.1. Is there a way of setting the access points so they are optimised for signal strength rather than distance - these only ...
We are noticing that we are getting alarms and time stats showing several AP's disconnect and reconnect within a minute. Is this normal behavior? I also ran a report for device Up Time and there are several that have an uptime less than a day. We h...
Resolved! Scheme priority boot up LAP
Hello,I would like to know which it is the sequence of priority that a LAP takes to choose a WLC. I explain my case:I have a DHCP server with the option 43 enabled where I assign IP of WLC, but I also have enabled OTAP on WLC. What LAP will choose f...
