HiThe LWAPP-upgrade on a AP 1131AG faield with the following error message on the upgrade-tool:"AP does not have supported radio"On the AP is still the autonomus image.Does anyone have an idea?
HiThe LWAPP-upgrade on a AP 1131AG faield with the following error message on the upgrade-tool:"AP does not have supported radio"On the AP is still the autonomus image.Does anyone have an idea?
Hi Guys, 2x Wisms on Software version 7.0.116.0 WCS Version 7.0.172.0 I am having problems with removing an old WLC entry in WCS.. The problem came about when I tried to delete the 2x WLCs in WCS and then factory resetting and rebooted them directly ...
I am trying to add new network device to a new out of the box ISE 3315 appliance under the Administration > Network Resources section. I was able to do this the other day but now when I try I get an error that says "Failed to create network device. ...
Hi, we upgraded from WCS 7.0.176.0 to 7.0.220.0 to make use of the enhancements to the DB engine.However, we are faced with a problem when we run the AP Summary report. We customized the report to be very basic as seen in the attached image. We only ...
Hi I have 3 2504-50 controllers with around 75 ap's.There are severeral ap-groups and H-reap groups on the tre controllers.I need to be shure to have the exact same config on all controllers to ensure failover.Are there an easy way to do this ?/Per B...
I need to set up a fancy new 5508 wireless controller, but I was a little confused about one thing:The management interface is obviously the one through which we map the wireless vlans, etc. On the switch side, this is set up as a dot1q trunk yes? Ho...
Hi All,I am a bit confused abuot the 5500 Wireless Controller licensing and AP support.Is it possilbe to order the AIR-CT5509-50-K9 Controller (This should support 50 AP and have the Hardware Capability to support 500 AP?)And then order L-LIC-CT5508-...
Does anyone know of, or have any instructions on performing an upgrade from a 4402 to 5508?
The web GUI timeout on my AP seems to be too short, if I login and sit idle for about 60 seconds when I select a different menu item I need to type in my credentials again. At that point I notice that on the login menu it says to login for priv acces...
I want to deploy a WLAN over a campus with a large number of buildings (3000+ users). On the whole campus there should be the same SSID so that no matter where people go, they always perceive the WLAN as "the same".Now, of course I do not want to mak...
WE have DHCP scope configured local on the WLC running code 6.0.188.0. Clients can connect to the SSID being broadcasted using DHCP and have access to the Network when I configure the same ip address as static on my laptop it works fine When we add ...
Hi I wonder if anybody has seen this problem in bridged netwrok environment. We have a pair of Cisco 1310 bridges configued betweeen 2 buildings the config on each is simple one as a root bridge the other as non root no spanning tree is running and ...
HelloIs it possible to broadcast 18 ssid for one ap group on the wlan controller?Whats is the limitation for ssid broadcast?regards,Alex
Dear,Does ASA 5540 support BGP routing protocole to be configured on it??im talking about the latest versions thanksAhmed
We have two wlc in the system 5508 and 4402.we config HA for 2 wlc, both wlc enable LAGWhen I connect 2 interface of 5508 to 2 interface (in a port channel mode on, trunk, dot1q) of acouple of VSS switch, I cant management 5508 through web any more,...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-17-2026 11:43 AM | ||
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM |
| User | Count |
|---|---|
| 4 | |
| 3 | |
| 1 | |
| 1 | |
| 1 |