Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I am working on deployment with over 600 3502i APs. The client device chosen for voice on this network is the Ascom I62. This device does not like to roam to APs using UNII-2 channels 52 - 64. I have removed these channels from the channel plan on my...
hi alli got a Cisco aironet 1131g (air-lap1131g-e-k9)i want to (if poss) change it to a stand alone unit as i dont have a controllerin flash ..Directory of flash:/ 2 -rwx 164 Jan 01 1970 00:00:34 +00:00 env_vars 4 drwx 128 ...
I am looking for a document from Cisco that shows the tolerance when using the 12vdc power option. I know that for the 1522, the tolerance for 12vdc is +/- 0.5%. Is it the same for the 1552 APs?Any help will be appreciatedThanks
Dear Tech Gurus, Can any one help me regarding channel assignament at root and mesh access points.will the channel be same on all RAPS and MAPS (5Ghz). With Regards,Chaitanya.G
Hi I have been told to configure Guest VLAN on WLC 5508 and ensuring no access to LAN network while connected to Guest Vlan. I am looking for best practises in configuring the DHCP for guest vlanthe security paramenter for authentication, the vlan co...
I have turned on the aaa command authorization without applying adequate privileges to the user. I can now login through that user but the ASA 5510 displays an error :ASA5510# show runERROR: % Invalid input detected at '^' marker.ERROR: Command autho...
Do somebody know what happen if you have passed half of examens certifications about CCNP Wireless Version 1.0 and you try the others on version 2.0, is that valid to finish the certification???
I have a WLC2504 and like to setup a WLAN for mobile devices. How can I configure to use Active Directory authentication?
The AP is connected to the WLC but keeps taking it's Raodio Down. As suggested I have played with the PoE settings to no avail.....Wed Feb 1 18:30:36 2012AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:ba:70:93:81:60 Cause=Radio int...
If the nomenclature is x:y:z, where x = transmitters, y = receivers, and z = spatial streams, and the 1262 is 2:3:2 (two TX, three RX, 2 streams), then what is a 3602 ?I've seen both 4:4:3 and 3:4:3. Are there three or 4 transmitters ? I get there ...
How to config the DHCP for wireless clients? Just wireless clients. This is standand alone AP. No WLCThanks,
I have a client that wants a wireless solution that will deny the entire domain machine (Laptops and co) within their organization access to the WLAN and permit only personal WLAN devices brought in by employees using thier domain username and passwo...
Dear all,can anyone tell me the ACL Ports/Protocols which must be openend (in- and outbound) to enable a communication between a CISCO Office extend AP and a 5508 WCS.Tx, HajoSent from Cisco Technical Support iPad App
Hi Chaps,Although the 7925 deployment guide recommends an overlap of 15-20% for adjacent cells, is there a min/maximum % figure that will still allow the phones to work. This is really to cover off previous data deployments where overlap is greater o...
I have a LAP1041N that I was given a while back and am trying to get it working but I don't have a WLC. Is there any way to convert a LAP1041N to an AP1041N so it will function independently?
