Wireless

There is currently no bootable OS on the AP and I must transfer an OS image from a TFTP server from the mode ap:and transfer it to flash Not using the web GUIPlease HELP!

Hi , I have four AIR-WLC4404-100-K9 controller and AIR-AP1231G-E-K9 and AIR-LAP1242AG-E-K9 AP's in production.Recently I connected one AIR-AP1231G-A-K9 AP to the controller after upgrading the AP to LWAPP image. It got registered with controller ...

Anyone have idea why the dot11Radio interface in AP 1250 stuck in reset status? I have tried to no shutdown in CLI and enable in GUI but doesn't work.Aironet1250#sh ip int bInterface IP-Address OK? Method Status P...

Hi,we are using an 4404 with 5.2 and one new 1142 AP. Now i have an HP Notebook with the Intel 4965AGN running Proset 12.4.0.0. My Problem is that i won't get any higher Data Rate than 54 Mbit. We have activate 40Mhz Channel on 5 Ghz and activate N o...

Dear gents, i am trying to make the access to the network via 2 things : SSID's key first , then using a username and password to connect, or at least username and password.i have aironet 1130ag , and 40 users.Any suggestions..

any idea why the ap 1310 send the interface to "reset" state:Feb 28 18:03:00.820 -0600: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up*Feb 28 18:03:19.870 -0600: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state t...

We currently have a client using 2x4402 WLC's, with 2xRAP(1520AG's),1MAP1(1520AG), 1 WGB(1310G) and 2xCCTV(AXIS) camera'sconnected to each of the MAP1 & WGB. we are using WLC Software code ver.5.2.157 for the 2 WLC'sScenario1: WLC(1/2)---SW---RAP1==...

Occasionally I receive alerts about some of my AP's are down. From what I see in the logs of WCS is that the WLC is changing the channel of the access point from channel 1 to channel 11 because of interference energy.Its great that the wireless impr...

I am trying to upgrade the firmware on a Cisco 1200 AP via the web interface but keep getting an error saying not enough room on flash.The firware currently on the AP is c1200-k9w7-tar.123-8.JA2 and I am tring to upgrade to c1200-k9w7-tar.123-8.JEC2....

hi all,For customer solution, I tried use WLC 526 with 5.2.157.0 (in release notes, local eap mentioned as new funkcionality, but when I configured it by WLC release 5.0 configuration guide - it doesnt work.from sh wlan <ID> command i always see that...

I ran into this a few weeks back as I was trying to get some demo depot gear working for a POC. basically all of the 1131 AP's would not join the controller and I got these errorsMay 17 20:45:42.471: %LWAPP-3-RADIUS_ERR: spam_radius.c:108 Could not s...

We have two 4402 and 23 1242AG. 4402s use 5.2.157.0 image. All APs resets often.In the Trap Logs there are a messages that APs disassociated previously due to AP Reset. Last reboot reason: operator changed 11g mode.It happens on both controllers with...

I was wondering what features are available from a managing and support perspective with the 4400 series WCS. I was specifically curious as to whether the WCS is able to identify serial number of Cisco AP's associated to it.

I'm getting an the following error on my workgroup bridge. And I'm not able to pass traffic across it. *Mar 1 00:03:29.665: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up*Mar 1 00:05:48.860: %DOT11-4-UPLINK_DOWN: I...