Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
now,when we use the wlc controll all the ap.sometimes,one ap can't accept any wireless user join it.so,we must reset the ap on the wlc.why???
Resolved! 1142 above the ceiling tile
Greetings everyone,I have a situation where the customer purchased 1142 access points and now decided that they don't want them mounted below the ceiling tile (on the grid). This is a college housing environment so they've had issues with things bei...
What port config should be used for a LWAPP in 'rogue detection'.Should this be a trunk port or an access port.Please advise.
This is not a Cisco product related, but in case someone can confirm I'd appreciate it:Imagine from a web server (let's say the Microsoft IIS web server thing) you generate a "certificate request" and submit that to the CA (Certificate Authority, Ver...
Has anyone seen deployment guides for Windows Network Policy Manager and PEAP on server 2008.Or is aware of any tweaks or issues with this and particularly Vista?
Hi,I've a WLC2125 ( 2.2.193 ) that I often found with no traffic on ethernet port ( with no LAG ) .After that I've to reboot the WLC to fix the situation.The WLC is connected with just one port.Any idea ?Many thanks in advanceLuigi
WCS 4.2.81.0WLC 4.2.112.0Loc 3.1.36.0I have a very large map with currently 40 APs placed on it. Tt will have close to 80 when completed. Layer that are on:APAP HeatmapsClientsRogue APsResaved AP placement and recalc RF prediction. Antennas are all ...
I have a wirless 7920 wirless phone that keeps losing IP settings, on the front screen it says "Authentication OK" but when tries to get a IP address it fails. The Wlan controller is 4400 series model number 4402
I am running 5 1252 AP's as "hotspots". I am using both the 5GHz and 2.4GHz radios. I am using a power injector to power the units. I am using 3 antennas on both radios and I'm using diversity mode. I can can see the A,B,and G signals, but no mat...
Hey all,I've been trying to configure my AP for a couple of hours now without any luck.I want my AP to hand out IPs directly from my ISP. I've done this before, and I remember it being very simple. I setup the BVI to pull DHCP addresses, and config...
i had a customer send me this bill of materials about WCS and i don't understand this i want info out every item.could anyone help me ,please.
HelloMy Configuration is:15 AP(1240AG 12.4(10b)JA ) 1x WLSE-1.1-HW (2.15.1u).One of the 15 AP is the local radius and the wds.Wds and radius works fine. All AP registered in wds.My Problem:After upgrade the wlse of version 2.15.1u the WLSE does no...
We are seeing what we perceive to be, less than optimal data throughput rates between the 1142 and the Intel 5300AGN.Configured as follows:WiSM w/ 6.0.182.0 code1142AGNWPA2-PSK AES802.11b radio OFF20MHz channelsWMM EnabledDell Latitude E5400INTEL 530...
Does anyone have Vocera and Spectralink successfully working within a LWAP environment running version 4.2.176.0. This will be my 1st deployment in implementing both vendors together. The Vocera badges are the largest of the two with only a handful ...
My problem is that I Connected an AIR-PWRINJ3 power injector to a device that is not cisco however it has a port PoE 802.3af but the power injector is not working.What should I do to make the power injector work?
