Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hello,I like to configure 3 Cisco WAP4410N as repeaters for every floor of an office. The adsl router is a Cisco WAG120N. I upgrade firmware to 2.0.2.1 WAP4410N.- I have one of the WAP4410N (1) connect to the Router Cisco WAG120N, configured like ac...
Hi everybody!I'm trying to backup my primary WAN with secondary backup connection - 3G WAN through Cellular 0/0/0.Point is that I need to track some external IP address on my primary interface, for examle 8.8.8.8. If it is not reacheable, then router...
I have one wlc 5508 running on latest IOS 7.116, there is one wlan abc which i have disable status and disable broadcast, but randomly still i can see from wlc dashboard there is one client connected to this wlan abc. The moment i check on the client...
hi,i have a network of APs connected to WLC model 4400. AP model 1242AGOne of the APs when i brought into network, it goes to exlcuded clien listIt is getting dhcp address......
We have a root AP whose status light is showing solid red. We power cycled it and it still shows solid red. According to the Cisco documentation, this indicates a firmware failure. Unfortunately, we did not get Smartnet with this access points and...
Hi,I've got a setup like this:WLC 5508 v7.0.98 6-7 Autonomous upgraded to lightweight APs - 2 * 1231G while the rest are 1242AG3 dynamic interfaces, 2 to Corp (diff VLANs) and 1 to Guest4 WLANs binded to different interfaces 2 to the Corp interfa...
Hello Every,I have just purchased three 3502i access points and am having a hard time getting them to communicate with my 2106 controller. Currently, i have the APs plugged directly into the PoE port on the WLAN Controller. From everything i have r...
I'm looking for a wireless handset that is compatible with a Cisco IP Phone 7940 Series. All I can seem to find are wireless headsets. Basically, I just need a cordless phone I can plug into the phones we already have in case we have to step away f...
Hi All,I am reading Cisco documentation on Wireless Local Area Network, but it is getting kind of confusing. If I need to design for wireless mobility in a network to support data, voice and guest, do I need to provide separate AP for data, separat...
Hello,I am trying to enable more channels in the DCA channel list for 802.11/b/g/n. However, when i hit apply i get this message: "802.11b network needs to be disabled to apply changes to DCA."I do not see a spot to disable B. Would this be somethin...
Looking for instructions on how to configure Wireshark to capture wireless traffic from a liteweight AP thats configured in Sniffer mode. The controller/AP configuration is easy enough, but looking for specifics on Wireshark config. Controller config...
I have finally got my office extend AP to connect to my companies 5508 controller by enabling NAT on the management interface and can see all the cooperate SSID's. However when I try to connect to the SSID my client either gets a local IP address fro...
Hi,I wanted to know if SIMO (Single Input Multiple Output) and Antenna Diversity are the same. I read that antenna Diversity can eleminate multipath distortions since it has two or more receiver Antennas. Antenna Diversity uses single transmitting an...
Hi,I read on Cisco documentation :The WLC's notion of inbound versus outbound is nonintuitive. It is from the perspective of the WLCfacing towards the wireless client, rather than from the perspective of the client. So, inbound directionmeans a packe...
I can configure this:I have a two SSID configured in the Wireless LAN Controller 4400, and I have one wireless station, and I would like configure the following:Wireless User A must connect to the SSID A only, and not to SSID B. Is possible block the...
