Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hello All,I have a odd one here....I have 5 AP1000 that used to connect to my WLC no problem, now they will not Join with the WLC.I receive the following error in the syslog "No board data payload found in join request" ???? I also have 10 AP1242 tha...

IrishMann by • Level 2
  • 1810 Views
  • 8 replies
  • 0 Helpful votes

Hi Folks!when u enable LAG on the the contoller with 4 GIG interfaces then on  switch side where the WLC is connected, do i need to configure this IOS Command:switch(config)#port−channel load−balance src−dst−ipor if note configured  then i will have ...

I have been asked by my boss to add some Cisco 7921 phones to our network.Currently we dont have wireless coverage.The wireless will be installed purely for voice.Can someone advise me on, or point me to some docs, to ensure I set the wireless up as ...

Hello,1231G AP boots fine in lab with power injector to several lab switches.  AP then is sent to branch location with same type of power injector, not the one that was used in the lab though and when AP is powered up, 3 amber lights show up, port sh...

b-ulrich1 by • Visitor
  • 2350 Views
  • 10 replies
  • 0 Helpful votes

HelloI have a Cisco AIR-CT5508-K9 running revision 7.Can anyone explain to me the differences between a guest type WLAN and a WLAN type WLAN please? I have searched a fair bit but can't actually find an explanation.Also, can any one please let me kno...

Hello,We are going to replace an aged 2106 controller (v4.0.x) with a new 2112.  I am wondering if there is a migration utility available (ala PIX to ASA) or if a import of the 2106 config to the new appliance will fly?.  Anybody try this recently?  ...

teeboli68 by • Community Member
  • 1442 Views
  • 3 replies
  • 0 Helpful votes

Since we upgraded our WCS system to V6.0.196.0 we are receiving a lot of the following error messages and I haven't figured out why.Client 'c0:cb:38:3f:a1:0d (anonymous, 0.0.0.0)' which was associated with interface '802.11a/n' of AP 'ACAA01-00.P04-G...

pannick by • Level 2
  • 6447 Views
  • 1 replies
  • 0 Helpful votes

Hello!We have the following construction:WLAN Controller 4402 with guest WLAN/Web Authentification The guests are led to the internet via a seperate Securepoint Firewall (transparent Proxy). Separated from the remaining enterprise network. My superio...

Hi, Everyone.I'm Daejin from Seoul Korea.Nice to meet you We are using IX train for ITP IOS.The ITP chassis is C7613.1) I would like to know a feature, main difference between IX train and IR train.2) I would like to know the reference using IR train...

superjini75 by • Community Member
  • 551 Views
  • 0 replies
  • 0 Helpful votes

Hello.We are experiencing issue with some of our AP in HREAP mode. In fact, some users are not able to have a valid IP assigned when they are connected to the Wlan. the only solution I have to help them is to reboot the AP.It seems we have the proble...

ybilteryst by • Community Member
  • 906 Views
  • 1 replies
  • 0 Helpful votes

I m using WLAN 4400 with4.1.185.0 code. I tried to create on more interface, it says "cant creat the port".However, it creates the port but does not take DHCP IP. It is also broadcasting that SSID. Any solution ?Many Thanks

adilhayat by • Level 1
  • 1738 Views
  • 9 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card