Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello All,I am trying to integrate a 3350 MSE to an existing WCS and I am running across some issues that I can't figure out. Basically I went throught the initial setup of the MSE and assigned it an IP in the same network as the WLCs I have install...
/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Normale Tabelle"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0...
Can you please advise.I will be required to setup a 2xWLC 4002 for use with several 1131 LAP connecting via a 3750 stack. what would be the recommended setup for the LWAPP? would it be best to use layer2 (boh the ap manager interface in the same vlan...
Hello mates.I have configured a Cisco 2100 WLC. I have configured two WLANs, one of them with Web-Authentication. When I connect to it, I get an IP address, and if I open the browser, I was redirected to the authentication page (in the browser toolba...
Hello,I'm trying to setup a 5508 to work with dynamic vlan assignement using the same SSID.I've followed everyting in this document http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtmlbut it doesn't wor...
I just upgrade my WISM's to 7.0.98.0. Since then my users have called saying that they get error messages on their 7925's and Vocera badges"searching for AP's". I don't see anything in the releasenotes for this. Any ideas?
We're deploying a project composed by AP1142N and AIR-PWRINJ3. The UTP patch cords are Category 5E. The access points work normally when powered by external power sources ( PWR-B= ). The problem occurs when access points are powered by the power inje...
I have a few other questions:1. Will either of these work reliabley if they are mounted vertically?2. Would a stainless steel wall plate mounted behind the WAP either horizontally or vertically reflect any appreciable amount of the radiated RF ener...
We are experimenting some trouble after upgrade about 40 APs from autonomous IOS to a controller 4402.Some areas seems to have their coverage decreased after that.Most complainig come from users who has 7921 IP Phones and walk through the coverage wi...
I upgraded my WCS to 6.0.188.0. When I did so I lost the ability into display Clients in Maps on the WCS. Do I have to convert to MSE?Is there a new license policy? Prior to this I was able to see clients in Maps. We do have a 2700 location server.
HiThis question comes from our CSC Facebook Community.http://www.facebook.com/CiscoSupportCommunityWho knows about Wireless Access servers 5508's and why they don't seem to want to proxy a DHCP request from a wireless client to a DHCP server?
HIWe're changing our edge switches from vlan 1 flat network to layer 2 trunk switches.1 trunk for data 1 for voice.New native vlan is 555.Since starting this, the APs are not displaying any CDP or connected users in WCS.Vlan 1 is being trunked.WCS an...
I saw a slide deck that listed a release date as 1QCY11, but I can't find any more information on the new 802.11n mesh AP. Does anyone here know more about it - specifically the part number that we'll be using for ordering when it gets released?
Hi All,I have a customer who is running a Nortel 2270 and 2230 APs. they is looking to deploy a new 5508 controller and I am sure at some point will upgrade the Nortel solution to a more modern Cisco based solution but at the moment if it's not broke...
We are looking to create asset tracking solution in office based on CISCO unified wireless product.The following CISCO device are available in office.- CISCO Wireless Controller (Model: 5508)- CISCO 3300 Series Mobility Services engine- CISCO Wireles...
