Wireless

Hello,I have WiSMs running code version 6.0.196.0. I have to deploy AIR-LAP1131AG-N-K9 in H-REAP mode.Q1. Does AIR-LAP1131AG-N-K9 require CAPWAP or can run off of LWAPP?Q2. Does anyone know how to find out if a WLC is running LWAPP or CAPWAP?Q3. If o...

Hi guys.I have server - Microsoft Windows Server 2003 SP2, that run AD, IAS, DHCP services, and Access Point - CIsco AP1231G-A-K9 (AIR-AP1231G-A-K9, c1200-k9w7-mx.123-8.JEA).Can i use RADUIS for authentication  wireless users (iPhone, notebooks and o...

Hi i have sorted the wireless problem and it works fine after such a long time searching around, Can someone please tell me how to access the camera through a web page i can do that by typing the http://(cameras ip address):(cameras port number) and ...

HiWe are just putting in a new Controller - 5500 typeWe are using a WCS .Someone has raised the issue of whether we can have multiple vlansper SSID - as otherwise we may have very large broadcast domainsdue to the overall design being to have  Maybe ...

I have a Cisco AP1142N access point where I can enable QoS.I have a few questions relating to QoS and how it actually works with devices:How does the Cisco access point      differentiate between traffic streams?What happens if the source of the     ...

Cisco wireless controller is sending out malform packets across the network.  Wireshark reports numerous malform packets with the source of the Wireless Controller.  when we unplug the WC the malformed packets go away and our network returns to total...

Hi,We have WLC 4402 & 30 No. of AP is connected. We are facing intermittent network disconnection problem.During problem we observe following thingsClient is not communicating with network while ip address is showing on client machine & sometimes yel...

Hi,Can anyone help with possible ideas why Apple MAC client and Desktop using 3Com PCI card migth not authenticate to the WLAN.Security implemented on the WLAN is WPA2/Enterprise with PEAP.AP 1140 seriesRADIUS server; WIndows NPSController: 4404Thank...

Hi Mates,need a little Fingertip...I have to couple ACS 5.2 and Windows 200x Directory. Is there a short Description of what to do? I read that nor BDC or Agent Configuration is needed, is that true? Which Parameters are needed to configure?Thx in ad...

Does anyone happen to have any information on this WLC error:MFP Anomaly Detected - 6 'Invalid Sequence Number' violation(s) have originated from the AP with BSS'00:1a:30:b9:4f:c2'. This was detected by the radio with Slot ID '0' of the AP with MAC '...

Hello Y'all?I need help with this .I need to establish a point-to-point link using 2  aironet1310AG radio's using external antennas (AIR-BR1310AG-E-K9-R). However while installing due to power surge, one of the radios blew out. While the replacement ...

HiWhen I am trying to open client from Monitor->Clients in WCS v7 I am receiving an error:Error(s): You must correct the following error(s) before proceeding:Error:No response from Server. Possible reasons are: the server is unreachable, your session...

Have 4 AP1252 installed.  Clients dropping off wireless every 20 min.Multiple clients running HP  tablets are dropping often and unable to connect for a period of time.   Log files on WAP show TKIP MICHAEL MIC errors.  Have already configured  the  "...

Hello I have a problem, i configured asa 5510 whit phone proxy the phones are there in unsecure modemy problem is that the phone not register whit the callmanagerthe messaje that appear in the phone is that "file auth fail:SEPXXXXXX"in the asa the me...