Where can I get the software to install the Aironet 350 Wireless LAN Adapter? Will it have a client manager? I think that's what the software is to switch settings as you change locations.Model: AIR-PCM352
HiI've been trying to upgrade the boot image of my WLC4402-12, even following the intructions in the Cisco documentation. The image is correctly transferred from the TFTP but when I reboot the WLC I just see the same old boot image. Please see the at...
Dear friends,We have an environment that uses WLAN controller and local and remote APs. Before configuring these APs (AIR-LAP1242G-A-K9) as HREAPs, is everything ok. After configuring it, they begin to continuosly restart. Please, check the attach...
I downgraded a 4400 from 4.2 to 4.1 and the configuration was lost. The release notes mention that this "may" happen. Does anyone know if there is a way to prevent it?http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn411850.html#...
Hello,I would like some clarification on the Mobility groups behaviors. We have 2 WLC 4402 (wlc-a and wlc-b) setup on the same DMZ and 30 AP connecting to the first one (wlc-a). We have setup the same mobility groups on both WLC. AP failover betwen t...
Hi,How can I enable SSID broadcast for a non-guest mode in Cisco 1100 AP? In the GUI interface, the broadcast selection seems always associated with the guest SSID; in CLI, I can not find the command.Any advice is appreciated.Thanks.
Has anyone ever observed the folowing :I have 2 ssids's , one configured for guest , one for internal.The internal ssid is configured with radius. The guest ssid does not have radius activated. However , people are able to log on the guest net with a...
I have an 1310 AP set as WGB to access an LWAPP wireless network with 1242 APs. My first tests are ok, but only if I set fixed IP address to the 1310 and the wired pc behind it. Is it the normal behavior or I should receive IP addresses from my regul...
I have a question with regards to Local EAP. After you have created your Local EAP profile and applied it to an SSID a client with the appropriate certificate and local net user ID is authenticated. Once the user is authenticated does the client re...
Hi, i have 1131ag but at controller 4402 i see Number of radio interfaces 2, 802.11b/g/n admin status enable, oper status up and regulatory domain supported, but en 802.11a/n admin status enable, oper status down and regulatory domain not supported, ...
I have a WCS 5.1.64.0 controlling 4402's running 5.1.151.0.I am using a AIR-CB21AG-A-K9 card (ver A0) with the latest driversWhen I try to do an rf calibration all I am picking up is the b/g bands - no 'a'.The AP's are running 'a' and the PC card pi...
Hi,Can anyone explain to me the difference between ad-hoc and mesh.I read in some places that mesh follows 802.11s which uses the mac80211 stack which is present in the 2.6 kernels.when we are creating a mesh network, the VAP would be in the ad-hoc m...
Hi all,I have some 7921G phones on loan to test out. But i'm struggling to get them to connect to our Aironet1200 AP infrastructure. The phone just keeps "Locating Network Services" then evetually states "Connection failed"We use PEAP on the APs with...
Dear Friends, I do have 7921[CP-7921-E-K9] ,which needs to connect to 1252 AP [1252LAP-E-K9] .controllers used is WiSM [5.0] Initially country code configured was AE and later was added US .When I try to connect to the AP , it displays on the phone ,...
Is there a way to determine which AP you're connected to?I don't have a WLC, but have several access points in infrastructure mode. Of course, all of the APs have the same SSID. Is there a way to figure out exactly which one I'm connected to at the t...
