Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
CISCO 4404 ALERTS TO BE GENERATED(mail has to be triggerred) WHEN WLAN CLIENT AUTHENTICATION FAILS.Is there are any options on WCS to enable Authentication Failure on WCS.I have already Enabled 1.Client authentication failure Alarm and Authentication...
Hi, a I have this question:To run the Cisco Spectrum Expert Wi-Fi is necesary a WCS running in the Wireless Network ? I have a Wireless LAN, with Autonomous Access Points and would like run Cisco Spectrum Expert Wi-Fi to monitor my WiFi Network.
Are there any known issues by installing an antivirus software or upgrading to (microsoft) service pack 2 or 3 ?
Resolved! Access Point Question
I have a Cisco AIR-AP1131AG-A-K9 wireless access point. This AP is an autonomous (stand alone) AP not used with a wireless controller. I used Cisco's upgrade tool & the correct image to upgrade the AP to LWAPP (so it could be used with a Cisco wirele...
Hi Experts: Please help me on this-How we can proof bandwidth utilization/throughput over outdor point 2 point connection, my customer wants 20MBPs throughput, plz suggest me do we have some software or some other way to proof it?
Hi, I am configuring a Nokia E66 (wich is v4 in Cisco Compatible Extensions, so it supports EAP-TLS) with WPA2 EAP-TLS against IAS in a Cisco Wireless Network and I always obtain the same error in the IAS event viewer.denied accesssAuthentication-Typ...
We need to implement WiFi access in a disco environment. Signal quality with std access point varying from 100% with a few persons present to 40% with a 1000 visitors present (GSM's, Bluetooth...). Is CISCO 1240 AIRONET (1242) AP a good solution for ...
I have autonomous APS with SSID - XX and LWAP SSID - XX both WPA2 and they are seen as two different signals? When they were set up as WEP users had no problems connecting to both and roaming from both?
Resolved! WCS RSSI
How do you lower the power levels on an AP in one direction? One of my APs has way too much power in one direction. I'd like to pull it back a little. It is mounted on the ceiling of a room that is close to a wall of the building. It is broadcasting ...
Hello.I'm trying to figure out some wireless connectivity issues that I've been having.First about my environment- I'm in a campus environment with 130+ APs (mostly 1010, some 1030). I'm running with a WiSM blade on software version 4.2.130.0.Second,...
I had an access point in WCS that we removed from the network and deleted the AP from WCS. It still exists in WCS under Maps as an AP to add to a map. I am unable to delete this as the AP doesn't exist iunder Access Points in WCS. It wouldn't be a ba...
Hi I have change the hostname of my access points in the WLC, but in the WCS the older names are showed ?How I can update this info ?
I have 2 4404 WLCs and 41 APs. these 41 AP connect to 1 4404 WLC. I want to added the second WLC as a backup WLC. since i have 2 6509 core switches , I want to primary WLC connects to core1 switch, and the backup WLC connects to core2 switch . Please...
Hi all,When i go to position ap's in the WCS, I get the following error:[ServletException in:/pages/monitor/map/campusMoveLrads.jsp] Cannot find bean antennaInfoList in any scope' I can add maps, add ap's, and can position them. It's when i goto sav...
Currently using WLC 4402 with about a dozen WAPs. I would like to start logging some messages to troubleshoot some association issues. The syslog does not seem adequate for this the issues I am having. I noticed the default SNMP traps but is only ...
