Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
I have a wet200 associating with a cisco air-lap1142n-a-k9. It associates fine but two issues.....1. wired clients connected to wet200 will not receive a dhcp 2. I can hardcode ip address but only allows for one client . IfI plug in another client it...
Hi board,hopefully anybody knows this or experienced the same problem Here's the problem:We are using autonomous Aironet 1242ag APs with 12.3(8)JEA code. There is a SSID with WPA1 (TKIP) configuration and PSK authentication. Guest-Mode is disabled. W...
hello,I usually configure aironet but this version 1242 G I can't undestand it. The IOS don't allow the command line (configure terminal or conf t) and you can't access in GUI cause http or https is configure . Really I need help :thanks !Take a loo...
I have a cisco 2100 WLC. How to I change the dhcp setting to point to a different dhcp server? I looked in \config\dhcp but all the listing appear to be for creating setting up a dhcp server on the controller and I want the cleint to get their ip add...
Can I consider ASA5500 with IPS a firewall layer 7 ? The lack of load balance solution not is a problem ?
Can anyone tell me what effect in relation to speed, an 802.11b client would have on a 802.11g client. In particular on a network using AIR-LAP1242AG-E-K9 access points. I have read elsewhere that when using older AP's the 11b client will degregate t...
Hi experts,Is it possible to create and remove SSID and associate it with a specific VLAN through SNMP? If possible, what do I need to do? Can anyone please provide me a direction on how to do it? Thanks!Difan
We received this question on our Facebook page. http://www.facebook.com/CiscoSupportCommunityACL on WLC 5508 ,i want to create saperate WLAN which has no access of my LAN and trafiic can directly go to the internet through switch-firewall-internet...
Can somebody walk me through setting up WPA or WPA2-PSK on a Cisco 1130AG?Do I need a server to accomplish this?
Hello,for planning where to place a Cisco Access Point 1130AG, I need to know in which area around the signal is provided and in which strength.Thanks.Andreas
On my WISM, running 6.0.182, I configured the message on the web login page with our normal disclaimer. However when the Guest Login Page is displayed for the users, the message does not wrap and runs on and on to the right. The spacing on the word...
Hi alldo 1242 ap's try to associate with WLC4404 using lwapp then capwap, how many times do they try lwapp? I have had them all connected to my controller, I have reboooted my controller and they are all taking a long time to come back on, why is thi...
Anyone know what WLC version is supported on a WiSM running in a 6509?Currently we are running 4.2.61.0 and i have noticed on the Cisco website that its up to verison 6.x.x.How can i find out what version our 6509 will support?
We recently purchased a dozen 1142's which I added to our 4404 controller running version 6.0.196.0.I can't connect with the 802.11n protocol to any WLAN configured with WPA2 Enterprise, WEP, or WPA Enterprise with a pre-shared key.I successfully con...
Hi all, I have ACS 4.2, I can't get it to authenticate my wireless clients. I am still getting EAP-TLS/EAP fail during HANDSHAKE. I triple checked my cert at both end and everything under advance setting tab is all good. I can use the same s...
