Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi All, Please don't mistake this post as spam. We're currently creating what will hopefully be a useful technical resource for all those Cisco Certified engineers out there.www.uccert.wikidot.com There are network diagrams, videos and links for fur...
We have 3 1231ag WAPs that are having problems with 1 SSID. Seems the signal is low.This in not on a WLC, so I guess it's CLI for me.... Can someone point me how to troubleshoot this? I am a newbie at troubleshooting wireless. How do I show how m...
Resolved! Restricting SSID to certain APs?
Can I map an SSID to only be broadcast on certain AP's from a 4404 controller? Seems like was able to do this in early releases but can't seem to do it now, just the AP group function..Thanks,
I have this environment:CME 7.0 running in Cisco2851.WLC2106 with 6 1242 APs15 phones 7921I have to extend the wireless coverage to an specific point (warehouse), 150 meters away. This point only have a PC and a phone, so I don't think a bridge is ne...
Can someone help me figure where the problem isI'm trying to change from WPA2-AES to WPA2-Radius but I'm not sure if its the windows server or the AP that I have the config wrong on how can I figure that out?
I have a 1310 wireless bridge....when I power it up, it sometimes does not boot up. The I LED will just sit there and blink and the R and E LEDs will blink in unison with it. After a while just the I LED blinks. I cannot find any literature that t...
I have a 1252 Ap that was booting to LWAPP software and connecting to a 4402 controller. It suddenly stopped booting into the LWAPP code. I can reach the Ap by telnet and it seems to boot to Autonomous mode. Is there any way to start the boot into LW...
Hello!We have an customer that has a installation with around 50 1130ap's connected to a Cisco 4404.The system is up and running but when we restart an ap it will not connectagain to the controller! (color cycle, red orange green you know ; )I does g...
I have a network of multiple WiSM' in different locations. Each has the same SSID's configured. They are all in the same mobility domain. They can all see each other when I look under mobility groups.The problem I am having is that my guest SSID a...
The following error msg occurs upon boot of C1231G:ap: Xmodem file system is available.flashfs[0]: unable to allocate available block.The system has been interrupted, or encountered an errorduring initializion of the flash filesystem. The followingc...
on my aironet 1130AG, my wireless in my building is up, but one of the guest accounts isnt working... i attached the config. NO CHANGES WHERE MADE, just the guest account stopped working a few days ago... HELP!
Hi,I'm providing a solution seems a hot spot for Internet, in some locations I need conect differents AP by physical wire, so with mesh I can do this, but the question is, It is possible to do mesh only for connect 2 or 3 MAPs without WLC, and what b...
I downloaded the passthru.tar and edited the login.html for a custom passthru authentication. However, I my Web Browser reports 405 Method Not Allowed when I click on accept.
As we all know and love, the 1000 Series Access Points are no longer supported past 4.2. And I haven't quite heard the fate of the 1510 Mesh AP's either. However, I hate for this to prevent me from going to 5.X when the time comes right. Since I use ...
Hi, what is the range for the 1250 model ?? It doesn't appear in the datasheet ! Thx
