Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
HiI am trying to connect to a remote Access point within our network..is that possible to enable telnet or ssh in the access point through WCS or https. please let me knowKarthik
For one of my SSID's I am using 802.1x with WPA2/AES. I have configured IAS on windows server 2003 and from the server message logs I am able to authenticate a user. I never complete the authentication through the eyes of the WLC though. In using deb...
In a WLC (6.0) environment:a) Can I use WPA-PSK (Pre Shared Key) with CCKM?b) Do i need any extra device?c) Do CCKM requires and external radius?Thanks
I have a client that is looking to fully lock down the 7925 phones. We have "Disabled" the "Setting Access" which prevents users from changing ring tones and volume, but a few savy users have discovered holding dow the "*" key will put the phone int...
Hi All,Configuring a standalone 1250, and need to configure the management IP. The management for the switch/access point are not the native VLan. On a switch I'd just go "int vlan x -> ip address x.x.x.x" But on an AP there is no such option, ...
It's been a while since i've set up 1310s and i'm looking for a good sample config that uses two 1310s as building to building links. What security to use is a concern. I also have an ACS server if that will help beef things up.Does anyone have som...
Hi PushkarHi, I have an airespace 4012 and due to a mistake on the update it caused that the equipment doesn't boot.I didn't take any copy of the firmware, where can i take this old version from (version 2.0.142.0)? or is it possible to bring it to...
So I have two 3560s with SVIs using HSRP.If I want to spread the 5508 across both switches am I limited to 1 trunk to each switch and I get to watch the other 6 GigE ports on the WLC collect dust since I can't use LAG. In other words the 5508 can't ...
I have 2 Cisco Aironet 130 series wireless bridges that are connected. Once or sometimes twice a day I must power cycle (Cisco Bridge1). Cisco Bridge 2 never has any problems. I have went through and checked all settings and verified the settings ...
/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in ...
I have a Cisco HWIC-3G-CDMA-S card I activate it and everything is good but my service provider asked me to change the MNC and MCC (Mobile Network Code and Mobile Country Code) but I found no command that can do it because it is CDMA and has no SIM ...
Hi,I have a WRV200 router and I set up three SSID on it. In one of the SSIDs I disabled wireless isolation. But for some reason two wireless computers in the same SSID can not reach each other. If I put on computer on the wired network it can reach t...
Can we update security police signature in wireless lan controller ?
Has anyone used an NM-16A/S serial connection to a WLC 4400?I have my termial 'router' working with the rest of my Cicso gear and I would like to use it for my Wireless LAN Controller 4400. I tried to use the DB9 terminal connector that Cisco sends o...
I have three different types of AP's going to a Cisco 4402, running 6.1.196.AP-1252AG are running fine.AP-1242AG are having very high errors in the outbound side.AP-1131AG are also having problems.This is an example of the switch's output. GigabitEth...
