Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi the Cisco NetPro community,I would like to have a discussion with you on the best way to configure a network containing a WLSE and a large amount of Access Points.The network I want to configure comprises some subnetnorks, each comprising about 10...
Starting a few days ago, two of my WISM-based controllers generated this message: "Keepalive messages are lost between Controller 'xx.xx.xxx.xx'and Master.Please check the controllers port configuration,any software or hardwareincompatibility issues....
Resolved! Heat Maps in WCS .... HELP!!
Hello,I have set up a LWAPP network for a hospital running all "A" with some hotspots that are "G" capable. Because of interference issues in the hospital I have disabled the "G" radio in all the access points that are not part of the hotspot areas....
We have a wlc 4402 (IOS 4.1.185.0) with a few LAP1131 associated to it.All the APs are located in different cities (one per city) and every AP is connected to a trunked Fa0 of an 877 router, that provides to the APs its IP address as well as the IP a...
Greetings, i need to service 13 access points and provide load balancing between all connected AP's.Fault Tolerance isnt a concern at present hence my reasoning below.I looking at specifying two 4402 Controllers with the 12 AP License and configure t...
Cisco Wireless LAN Controller 4402 can support lightweight access point 1242 over wireless backbone or need ethernet connection?
Hi,Anybody outhere had experience problem with non-cisco antenna connected to Cisco AP? I had this one external antenna 12 DBi outdoor omni that connected to Cisco AP1242AG - LWAPP. The performance that not really realistic and the signal keep showin...
Hi there,I got the strange messages on my wism(v4.1.158.0)Jul 03 14:41:24.148 apf_foreignap.c:1246 APF-1-REGISTER_IPADD_ON_MSCB_FAILED: Could not Register IP Add on MSCB. MSCB still in init state. Address:00:1a:70:a6:b9:feJul 03 14:41:22.821 apf_fore...
I have several 1130AG LWAPP's running 12.4(13d)JA connected to a contoller running 5.0.148.2 SSID's are broadcast - usually no problem.However, I've noticed that several different vendor wireless cards cannot see both SSID's.Running a wireless captu...
Hi All I have problem with my wireless access point when I connected to the wireless adapter I can not ping one IP address, other ip responds. The ip address that I can't ping is a network load balancing address between to server'swhen I is connected...
I need to intall 04 Aps in an area where all of them have contact. I now know that the best practice is to use the three channels combination, but what would be the best way to do it? How could I use the 4 APs considering that two of them will be in ...
Hi All,please can somebody help?I was doing a simple test today with 2 AP's, both AP's are powered by Cisco Power Injectors. I was expecting that my client would simply switch association from one access point to another if I disconnected the etherne...
Resolved! Patching WCS server
Hi all,I have one servers running WCS v4.2.62.11. It is a Window server 2003 R2 standard edition service pack 2. I am currently going to patch Microsoft vulnerabilities patching on it. Is it going to impact WCS? Anyone has encountered installing Micr...
Hello, We are trying to get a 1242AG access point to have users connected to it to authenticate on it to the ACS server. The 1242AG has a new menu - AP authentication. Has anyone delt with this menu and gotten this setup to work? Version is 12....
In the GUI of a 4402, I have 2 - one way deny rules for http and https traffic.If I block 1 way, do I have to block the other way too?If so, why?Thanks!
