Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello Every one,Help me to understanding 9800-L WLC.My current network structure is 3504 WLC and 1815i access points. Planning to upgrade WLC 3504 to 9800-L. After upgrade the existing 1815i access points will join to 9800-L WLC? or need to buy any l...
What should be ideal AP connected swich port configuration? We have configured below config in our environment but sometimes facing issues due to same. Please confirm if there is any issue with below config. Access point InterfacesLocal model Access ...
Hi All, finally got some MR57s for testing.Unfortunately I missed the memo (and still cant find it)...Apparently iPSK without radius is not compatible with 6 ghz? Regular PSK doesnt give any issue, but iPSK says "This SSID will not be broadcast on th...
VLANS allowed on Trunk are correct for Data VLAN. Both switch and router onsite have TACACS Functionality and Radius/TACACS server can be pinged from AP's on dashboard. But Packets do not return to AP's and test on SSID that will be utilizing Radius ...
I recently acquired the administration of our wireless network. We have approximately 175 access points within our main campus. The access points are all on the same VLAN. We are using tags to distributed the wireless clients across 5 other VLANs....
Resolved! AP Enclosure
Hi,I have a site with MR76 and they have the MA-ANT-20, and I'm looking for a recommended outdoor enclosure, Regards
Hello everybody!Does anyone know if there is any quick way (into a "Network\Wireless\SSIDs\Configuration Overview") to return an SSID profile to its factory "Unconfigured" settings?
Hello All,I was trying to convert my cisco c9124axi to ewc, I use the commandsap-type ewc-ap tftp://x.x.x.x/ap1g6a tftp://x..x.x/C9800-AP-iosxe-wlc.binAfter reboot I got the error EWC-AP in Recovery Mode......Please use 'archive download-sw' to upgr...
Hello,I'm seeking assistance with a situation involving two companies operating under the same umbrella, each with their own 9800 Wireless LAN Controllers (WLCs) and over 400 Access Points (APs) connected. Currently, our Rogue AP list is extensive, w...
We are having an issue where the guest portal is not bringing up the redirect page for authentication. We are using a Cisco WLC 5500 and use ISE version2.4.0.357 patch 8,11. On this issue, the AP in question is part of a flexconnect group with other ...
Resolved! Is it possible to retrieve a comprehensive list of all wireless devices with a specific policy?
We use a specific group policy to allow VIP devices to connect to our guest wireless networks without going through the SMS/Splash sign-in.Is it possible to retrieve a comprehensive list of every client with this policy applied, for audit and clean-u...
hello I'm trying to access the AP after setting up, but I can't. Is it possible to do log analysis? ap->radius server Ping communication is possible. ID/PW is also correct. When I try to connect to ssid on my device, I can't connect and the logs a...
I have a WLAN configured and in the radio policy section, I am getting the message "although enabled, the WLAN is not operational on 6GHZ Radios due to one or more missing required configuration (WPA2 disabled, WPA3 and Dot 11ax enabled) (see the att...
Dear All,I would like to test a anchor mobility with 5508 and 9800.Both controller can ping and reach other.But status keep show "Control Path Down".For 9800 is using 17.3.2a version and 5508 is 8.5.164.216.I tried to reboot those controller but stil...
I've been trying to setup a virtual 9800 to support LDAP for one of the SSIDs but haven't had success. I followed the instructions here: Configure Catalyst 9800 WLC with LDAP Authentication for 802.1X and Web-auth - Cisco and as far as I can tell ...
