Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi board,Does someone of you have a calculation for an antenna cable loss? For example:I have an antenna-cable that absorbs 3dB - how much AP output power is needed to balance that absorbation?In the document http://www.cisco.com/en/US/prod/collatera...
Dear all, I am facing the problem with WLC 4402 . I am using thirty 1141n AP with WLC 4402. In some Access point , it is showing LOAD Profile failed as the the number of client connection exceed 12.I need min 25 client to be be connected to the acces...
Folks, Is Aironet 1231 end of line. I am trying to configure AP authentication on it using fast eap but do not see the option to do it.Thanks,Parwal
Standalone 4404 - from what I'm reading with 5.1 and above (Document ID: 69561) I should be able to add more than 24 members to a mobility group. Has anyone had any luck with this - adding more than 24 members on a single controler?I upgraded to 6.0 ...
We have an issue of APs losing communication to the WLC, going into standalone mode and not completely returning to LWAPP mode once communication is restored. The controller is a 4404 running version 5.2.178.0. The WLC is at our corporate office and ...
Hi,We have project with 4402 Controller with 1310 LAP's. 1310 LAP doesn't support mesh topology. 1242 LAP does. Can I use 1310 LAP as root AP and 1242 LAP's as Mesh APs. Does it work?Thanks
Can anyone tell me what benefits (if any) would be realized by migrating to 802.11n access point in an environment with no 802.11n clients? I understand the idea of being able to migrate clients gradually, etc. But that migration is going to take man...
I have two WLC's and a 1131 that gets a ton of clients. When it got up to around 16 clients people started getting kicked off, however they were all sharing the same username and password. I was wondering if this is either an issue with max clients t...
Hi, we need to install wireless in a hard environment (with explosive atmosphere) classified as ATEX zone 20 and 21. Have anyone of you deal with something like this? In Cisco website we only see the ATEX certified in the AP 1522HR, but we don't know...
Hey guys,I have a guest access setup with WISM and Anchor controllers in DMZ for internet access. L2 security policy is based on WAP2+PSK awith Layer3 on web authentication. Would it be possible to let un-authenticated users to connect to some web si...
hi! we are autonomous AP 1242AG IOS(12.4(10b)JDA operating at 802.11A for Wireless 7925G IP phones. It's working fine with authentication type PEAP (using Cisco ACS) and WEP as encryption.On 7925G phones, there is setting for authentication (LEAP, WE...
What is the effect if an external antenna is connected, but the radio configuration has the "External Antenna Configuration" disabled?Is the radio functioning on the internal antenna only, or is the external antenna functioning without a set gain?
Hi,Has anyone changed a PSK key via the ssh sheel?If so could you send the cmd's please?Jamie
Hi, all I wonder exact meaning of the path retransmit and assoc retransmit in "show cs7 asp detail" =====================================SG1#sh cs asp detail ASP name: MTS_A Type: SUA Availability: enabled ASP id: n/aSCTP association state: establish...
Do with AP romaing in same subnet is possible, our client have four building, they are using 120 Wireless IPPhone using CME 7.x. It is possible to have romaing with the four building with same subnet with CME 7.x setup.Could please some one can light...
