Connection through hyperterminal, I am getting "system running-config write error; configuration failed. How do I resolve this. thanks
Connection through hyperterminal, I am getting "system running-config write error; configuration failed. How do I resolve this. thanks
We cannot get RRM RF Group Leader to update the RF Group Members. On our group leader controller, it sees our other controllers in the RF group. We have APs assigned to all four of our controllers and the tx power and dynamic channel assignment do no...
Hi All,Last week, I tried to test association PDA brand HP to associated to LWAPP AP. Testing with 50 units PDA. only a few number of PDA can get IP addresses then. associated only in 30 seconds, once trying to download/access to internet then get lo...
I'm replacing 2106 controllers with Cisco 2112 and 2125. During the replacement APs fail to backup controller but then they never go to their own controller, I had to wait more than 2 hours before it joined the controller, I have never seen this befo...
Hello,I have a brand new 1131AG access point and I am trying to configure it.I have plugged it into a lynksys router that is providing DHCP and it has given the access point the IP 192.168.1.101.When I try to connect to this address in my browser it ...
I am trying to do anonymous PAC provisioning to some new 7921 phones with ACS 4.2.0.124.6.I have created a user & pwd on the phone, and added this user to ACS.I have configured the WLC, ACS & phone as per the 7921 deployment guide (though there are a...
Is there anyway to assign users to different vlans with ACS/Automous AP's? I know how to do this with CUWN but not with Autonmous. Any ideas?
Hi,having no problems to get the AP's attached and configured via the WLC, but i'm not able to get the DNS-resolution in the LAN done proper.That means: Having 3 AP's connected to WLC2106, this one is getting it's DNS for one SSID/VLAN from an extern...
Hello everyone.I have a client looking at deploying guest access to several sites. The issues are that all the sites arevariable in size so we are trying to get a one size fits all which is difficult.Generally all sites will use controllers or HREAP ...
Hello, I have a WCS with version 4.0.97.0 and two controllers with version 4.0.217.0. and two models APs: AIR-LAP1242AG-E-K9 and AIR_LAP1131AG-E-K9. The problem is that I am unable to configure the templates WCS WLAN Override. I can set the controlle...
Hi,I'd like to know if there is a way to authenticate using a username with PEAP and in addition restrict the access with the station MAC address. Im using 1230 APs with Cisco Secure ACS authenticating with the Ms AD.Thanks in advanced
I upgraded my 1131AG AP from autonomous to lightweight with file "c1130-rcvk9w8-tar.123-11JX1.tar". Now, I can't get the AP to join my WLC, and the lights on the AP constantly blinks red, orange and green. I can't get the AP to get an IP from my DHCP...
Is there any way to prevent users with a virus from accessing our wireless network? Intrusion Protection and NAC are not yet installed. Would I need to temporarily enable MAC filtering on the WLANs and add the MAC of each wireless device I have verif...
How long can a HREAP AP remain in standalone mode without a controller?And how do you extend the timer?
I have a 4402 WLC configured on the management VLAN and 9 AP's that were converted to LWAPP. When the AP's attempt to connect to the WLC, they download the image then display the following error. "No more AP manager IP addresses remain." The AP's the...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-17-2026 11:43 AM | ||
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM |
| User | Count |
|---|---|
| 4 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |