Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi, I issued the 'sho dot11 assoc' command on my 1100. This 1100 is configured for a single SSID of AirYork. The results (shown below) show the associations to the AirYork SSID but it also shows other MACs that are 'not related to any ssid'. I've...
I just installed our first Mesh with 16 1500's, 7 are wired, (4 provide the A backhaul 3 for coverage only)9 are wireless. I would like the Bridge link to be "auto rf" and the coverage (G) to be manual or custom.All came up but on some of the A radio...
Greetings.My AP1240AG runs 12.3.11-JA4 code, works fine, but I can't enable https on it, SSH is working fine. I need both https and SSH both.I've tried the same config on my 1231BG units, and that works perfectly with the same config.Anyone heard of ...
Hi, I really dont know if this issue is applicable here but I am desperate for help now. We have a wireless project providing internet access in a very remote location. There are wireless mesh accesspoints connected back to back by wireless Point2Mul...
Hello,I am trying to setup an IOS AP using 12.3(8)JEB1 to use WPA2 using ACS 4.0(1)Build 44. I am trying to use PEAP with MSCHAPv2.The problem I am having is that the only way I can get the client to associate, is if I configure the the AP's SSID to...
Sucks. Website support is so convoluted, it leaves one going round and round in circles. Just trying to find out if my AP firmware needs updating or not is impossible. Then when I feel I'm getting close to finding the firmware, I'm given a choice o...
is it possible to run multiple ssids on an 1242 with different encryption. ie. one will use wep the other is a radius client that uses wpa2
i have a 1200 that i tried to switch to IOS. the reflash started and seemed to go for a few minutes and then an error message. something about reset in 10 secs? now i get all three leds solid green. if i try mode reset switch it cycles through or...
is there a way to replicated access-list to multiple waps instead of logging into each one indivdually.
Hi,Is there way to configure AP 1010 over a WAN. I have WLC4402 (ver 4.0.179.11) at central location. I came to know from cisco document only 1030 and above will support REAP for WAN Support.Please help.Karuna
Good Day,We recently installed a 2106 controller and 1130 access points. This question regards the maximum number of users for a given user name.We host events with up to 100 users. Ideally, we would issue one user name and password for the group. I ...
Hi,If I have all my users going through Dynamic Interfaces (ie. not Mgmt i/f) and these users are the only IP devices using DHCP (APs have Static IP addresses configured) then is the Mgmt i/f DHCP server IP address which the WLC inital setup dialog a...
I have multiple AP's in an arena enviornment. Now without violating the rule where an AP is assigned a non-overlapping channel, what is best practice if there are neighboring AP's within close proximity of each other and they are assigned the same ch...
I just got six 521 AP's. If I plug the laptop to the Console port, I see errors reading the flash image. I have tried this on two of the six. The CCA software does not see these units either. Any ideas? Where can one get technical level info. on...
Hi,On a WLSM with about 60 x 1231 APs.I login to AP & observe the output of this command,sh dot11 associations all-clientFor some clients "Key Mgmt type" is shown as WPAv2-CP and for other clients as WPAv2.What's the difference & what does CP mean?Go...
