Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
As my understanding, WiSM enforce QoS at the controller level, not at the AP level. For example, I set average rate to be 1Mbps and the user generate 50Mbps traffic. The traffic still used up the AP bandwidth and is throttled at the controller. Will ...
Resolved! 1242 AP stuck in oper down status
Hello,I recently deployed a 1242a\b\g AP. I can see it in WCS (version 4.1). However, the radio's are stuck in a oper down status. At first I was getting an error that the power was insufficient. It is set up with an ethernet power injector. I switch...
HiWe've tested MS Vista native supplicant on a SSID configure for WPA1 + WPA2 on ours WiSM. It wont work.We've repeated the same test using a SSID configure for WPA1 and it worksFirst question : Why ?Second question : What the difference between <wpa...
Hi, I would like to controll traffic from LAN to outside using PIX-FW and Radius. I have found these links which describes the method of controlling access using Radius attributes mapped to users or Groups in Active Directory. What i understood is th...
Hi We have controller based wireless network we are running PEAP till date now we want to go for EAP-TLS along with PEAP. I have configured the EAP-TLS but not PEAP is not working as well as EAP-TLS. Can any body tell me can both work together. I hav...
I have installed a Ap 1200 in a lab running novell 6.5 on 29 workstations with wireless adapters and after the twelfth computer logs in the ap kind of bombs out... Do I need to put another ap 1200 in this lab or is there some configurating that I can...
Currently running WCS version 3.0 and have been for the past few months without any issues. July 10th the java service experienced "issues" and since then we have been unable to start the WCS. The Database server starts up no problems but the Apache ...
Hi, i need to configure a ASA5510-SEC-BUN-K9 in my office. i need to know if there is an configuration tool, or every thing is done by cli. If there is a configuration tool, where can i download information about it, and if is only by cli where can i...
I generally deploy the 1231G cisco ap's along with two 5dbi cisco antennas [air-ant2506]. My predecessor used to purchase 6' antenna cables to go along with them.I found this odd because the cabling tech would only mount the antennas about a foot an...
Hi,I'm designing a wireless NW with one wireless Controller and 12 LightWeight Access Points, I will assign an IP address for the management IF from the same subnet for the LightWeight Access Points. I have the following questions:1- Can we assign a ...
871W with 2VLANs, VLAN 1 is native VLAN for cable connect. VLAN2 is for wireless and the wireless clients can associated to this VLAN2 and can reach Internet but some website cannot reach such as www.info.gove.hk and Windows Live Messenger also canno...
Resolved! Ports
If WLC behind the fire wall (In DMZ) and the LWAP internally,What are the required Ports to be Open?Thanks in advance....
The Corporate I?m working in, is looking at the WLC to control our 10000's of AP's and i was tasked to learn it and to be the "to go to" guy for this matter. I?m first going to test it with a AP1200 and Cisco router 1700 and a switch 29xx. from what ...
Clients do successfully connect but do not get an IP address. This is happening to any access point they connect to.
I will be rolling out the Cisco aironet wireless A/B/G PCMCIA cards to some users soon. The profile setup uses PEAP with MS-CHAP v2 for the authentication process. When the wireless radio is on at the time of booting the laptop, the Cisco software ...
