Wireless

How do I convert passphrase to hexadecimal for AIR-AP1121G?

I'm using the internal WLC DHCP to assign DHCP addresses to our APs. If you have more then one scope defined in the internal DHCP how it is determined which scope the APs use versus clients on a WLAN?Ran into an issue last week where our APs started ...

We have 2 Cisco WLC 4404s and 38 LAP1242AG access points. Approx. half of the APs associate with one WLC and the other half on the other. We are experiencing speed fluctuations when stationary and lose of connection and speed fluctuations when walkin...

WCS Version - 5.0.56.2 (on a Linux box)WLC Version - 4.2.112.0Problem is that i initally started trying to set up a Lobby Ambassador account and the WCS didn't see my WLAN's that were created with Webauth. After this i tried to manually refresh the C...

Hello, I'm hoping someone can shed some light on what I'm seeing here. I have WCS 5.1.x.x and to WISM's also running 5.1.x.x. I have a few LAP's converted from autnomous which and are being managed correctly. Here's where I'm getting thrown off. I'm ...

I just purchased an AT&T Tilt and hope to be able to use it in a wider audience at our company, however I am having a problem that may force me to return it and look for a different platform.I can connect the Tilt to my home WiFi network (Open/WEP) w...

I have 6 4404 controllers and a WCS (5.1.64.0). If I use the migration template in WCS to convert an 1121 AP to LWAPP the Self Signed Cert (SSC) is installed on my first controller. I can then audit it in WCS and import it to WCS. It then shows that ...

We are looking at providing internet service to subscribers via wireless 802.11. I am looking at using PPPOE and Radius for authentication. Is this still the best way to handle authentication for fixed wireless subscribers? If so what is the best way...

I am trying to NAT the same external address to three different hosts but using the same port.static (inside,outside) tcp 63.76.x.x 8224 208.x.x.29 8224 netmask 255.255.255.255 static (inside,outside) tcp 63.76.x.x 8224 208.x.x.23 8224 netmask 255.25...

Hi I am looking for some help configuring my 1242AG's in a Workgroup bridge configuration with EAP authentication. I have 2 1242's (AIR-AP1242AG-E-K9) one configured as an AP and ones as a WGB.With WEP I can get wireless devices to connect to the AP ...

I am going to buy a AIR-AP521G-x-K9 with IOS software which is a stand alone access point.However, later on I may buy a Cisco 526 Wireless Express Mobility controller in order to expand my wireless network.As I know at that moment I need to buy light...

hi guys, i have a air-br1310g-a-k9-r box. i had the firmware c1310-k9w7-mx.123-8.ja on it.i upgraded this unit to the firmware c1310-rcvk9w8-tar.124-10b.JA3after doing so my unit doesn't work any more. I'm getting the error the messages as posted in ...

I have an LWAP connected to WIsn on 6500. I want to clear the config and manually configure static IP to set it up on a network where I do not have any DHCP server.I read in the doc: http://www.cisco.com/en/US/products/hw/wireless/ps430/products_tech...

I am planning on setting up a Hub and Spoke Wireless Bridging Scenario, with a 1242 Access Point as a Hub and 871W Routers (with PC's attached) at the Spokes.Cisco does mention that 870 Series Routers do not support repeater or bridging functionality...