Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi, We are working with an Autenthication Server with Wireless Network, the AP´s are located on diferent LAN´s, but the problem is that some users get disconnection constantly, while anothers users are working without problems, same AP or diferent, y...
I have a cisco 1400 that that show interface show int dott1 radio interface reset protocol down. I had a surge in the area and had the problem after. I copied the config over to a new Ap and power injector and the problem persists. The bridge is the ...
Hi there guys,i wonder when are we gonna grab cisco's wlan card with atleast these spec's:1) 802.11(a/b/g & n)compatible2) Express card interface for notebooks (i'd prefer the L-shaped; less ackward than other)3) Chipset with strong "packet injection...
hi,do cisco offer a really nice graphical survey tool that integrates with WCS ?I need to do an assisted site survey, can i use WCS (thought it was just a monitoring tool,config tool for use on a server/pc) I need to walk around and click to point ou...
Hi,I upgraded my WCS to 4.2. After that, everytime I want to configure an accesspoint, I get an error message ""Tertiary Controller Name: This attribute is MANDATORY. Please Specify it".How can I turn that off? Thanks
Hi,We are considering to implement 1250 AP with 802.11N standard and use wireless IP phones.I'm not a voice expert but I can't find a cisco phone which supports the 802.11n ( draft ) standard. Is there a phone which supports this and if not when will...
Hi allThanks in advanceI have 5 1200 access point.i want when i add mac address to one access point it shoult be syncronize to other 4 ap also.i mean when i gave access to someone i have to add that mac address to each and every ap. is their any sett...
We currently have a seperate DSL line connected to a Linksys wireless router/switch for public use. We were given an 1130AG access point and would like to find a way to use a switch port off of the Linksys to connect to the FA port on the 1130AG and ...
I have 1242 AP whose IP address is configured as static. I need my clients to associate with the AP, and get IP address assigned by AP. But I didn't find any option where I can put the range for the DHCP. Kindly guide meCheers
I've been searching but I cant find any document that describes how to configure Radius authentication (and accounting?) with guest access. What attributes are needed to set up a time limited guest user etc..Anybody got some manual or step by step in...
HiI have a need for a 3G connection into the Internet cloud by a "device". This device will then provide wireless connectivity to laptop users. BUT I MUST restrict the laptop users to two specific Internet destinations. Is there a singlr box solution...
We are doing a site survey for wireless infrastructure. Redundnat controller implementations is what we are looking at. We were informed about using 2 controllers for redundancy but now during site survey, it has been informed that a different versio...
Good morning.I've got a problem on my 1230 & 1240 APsThe association with clients is running well, but every time after a short period (less than 1 second), the AP deauthenticate the clients, showing me this log : Mar 1 00:14:45.979 Information Inter...
It gives a "error loading flash:imagename" error and goes to a default ap: prompt. The image on the system may be corrupt. How do I configure this ap to boot to another better image?Thanks!
Can the cisco 1231G autonomous become a LWAP and Join a WISM controller and be and be managed by the WCS. I tried doing the upgrade to 12.3(7)JA3 as recommended by CISCO. But there were no option to join a controller.
