Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Is it considered best practice to use the internal DHCP servers on the controllers?I am experiencing a rather strange issue where I get seemingly random disassociations on my WiSMs.I am running a WiSM on software 4.2.61.0 and WCS version 4.2.62.0. My...
We have a 1200 AP (ap1220b a k9) with a AIR-ANT 5959 connected. The radio interface shows up. SSID is set to broadcast however we are seeing no signal by multiple laptops. We have tried unplugging the antenna and placing the PC next to the AP with no...
Hi Guys (& Ladies?),I have a 4404 running 4.1.185.0, with a number of 1130 AG Access Points. APs are in different subnets, and were provisioned using DHCP - this all works fine.Problems begin if I reboot / lose the Wireless LAN Controller. The APs co...
i know this is probably a novice question, but i really cant find the answer... what i would like to know is if i can route LWAPP through a VPN connection from one LAN to another through a PIX 506E ASA.what i would like to do is have a 4400 WLAN Cont...
Hi, I have a test environment with Light weight Access Points, 4404 WLC, ACS v4.0, a stand-alone CA and XP wireless clients. Can I get EAP-TLS with machine authentication(certificate based) without requiring an external AD database? I am getting auth...
I have a customer with LWAPs that are associated to a specific controller. They want to change the controller it's associated to, but it keeps returning to the original controller. They've tried assigning the Primary controller via WCS/WiSM, resettin...
After correctly stopping the controller, we shut the router off to replace another interface. After powering up, the service-module wlan-controller 1/0 status responds with "waiting for registration message" then "trying to recover from error". After...
Greetings, ive configured the 4400 controllers before and am familiar with the terms involved, ive recently acquired a 2106 controller, i have assigned an AP Manager and Management Address to Port 1 on the same subnet and can ping the device.Subseque...
I have the following scenario:WLC01 on 172.16.72.200AP on 172.16.72.4 (DHCP)WLC02 on 172.16.32.200 (different subnet)I have DHCP servers on each subnet, and routing between them is operational.The two WLCs are on the same mobility group and they can ...
Hi - Can somebody tell me the best way to enable and configure the wireless capabilities on a c3825 ? It already has a HWIC AP card and i can see the dot11radio interfaces as admin down. My client already has a seperate LinkSys system and wants to mi...
I have taking over this gear from previous admin. we want to upgrade versions to the latest.we have: Cisco 4402 ver.4.0.179.11 50 ap supportCisco 2700 ver.2.0.31.0WCS ver.3.2.40.0I have installed WCS ver. 4.1.83.0 and restored that old DB on new serv...
Hello,Please help I have read every doc on this AP and this antenna. there are three jacks on the radio labeled a - b and c. There are three cables on the antenna. which cable corresponds to the correct radio antenna label. Or does it not matter. Loo...
We are about to upgrade ACS from 3.2 to 4.1 and I understand the format of the PAC changes in ACS 4.x. Is this the chase, and will all users need to be provisioned with a new PAC?
Please let me know if my config is valid. Sorry i don't have visio's but from what you see, syntex , etc..does it look ok? do you see any problems with this. attached is the complete config for the ASAWeb Site Piece (External)access-list acl_inside p...
What am I doing wrong? I have configured a blank 857w with the config described here:http://www.cisco.com/en/US/docs/routers/access/800/850/software/configuration/guide/wireless.htmlHowever I get an error when I no shut the Dot11Radio0 interface conf...
