Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
hello we currently have 1 4404 controller at site A with around 70 APs spread over a number of sites. we're planning to expand the number of APs and intoduce some reiliance to the WLAN by installing a wism in a 6500 at site B to the 4400.the plan is:...
my 1240AG is in lightweight mode, when i connect the console cable( supplied by cisco) there's only output information displayed on my SecureCRT, any input is ignored and no display. what is the problem ?ps. when i connect the same system to a 3750, ...
Is it possible to configure an AIR-LAP1242G as repeater? I can't find an option in the Wireless Controller 2106.
Hi, I need to design a Voice wireless network. I want to use 1500 APS for outdoor . But I need to know if the 7920 ip phone works with the 1500 bridge.I see the 7920 datasheet, and just support this access points: Access-Point Support Cisco Aironet? ...
Hi,I'm currently configuring a WLC4402 with AP1130 in LWAPP. On the remote site, AP1130 are using H-REAP mode just to be sure we will not use the LWAPP tunnel to access the Internet. That part work fine. After that, I want to use Web Authentication w...
Hello, Iv got 2 BR1310 in slave mode and 1 in Root Mode, it works good but I need to install another BR1310 that is not accessible from de root directly. So I ve install antoher BR1310 with Omni antenna in slave mode but the BR1310 that is too far ca...
I have a WLC that I need to replace with one that supports more APs. I have configured the new controller identically to the one I am replacing. When I put it into the network only 9 of the 12 APs connected, and all of the radios were showing down. A...
Hello Pros,In the current running network, The wlc 2006 suddenly found dead and i replace with new 2106 wlc.There were 4 LAPs in the network working with old wlc 2006.Now i have done the below and the result is wlc not reachable from the same network...
Hi,does anyone had troubles adding controller to WCS 4.1 using SNMPv3 ?I've the following devices:- wlc2006 4.0.217- wcs 4.1.91On the wlc i've enabled ( as is by default ) SNMPv3 and I created an SNMPv3 user but when i try to add to WCS I get error (...
I have a LAP 1130 with 4404 WLC controller, The Windows 2003 DHCP is on another subnet, the Checkpoint firewall is between these devices. When I plug in an 1000 type AP I have no problems,(AP 1000 gets DHCP address, connects to WLC etc). But when I p...
I see a scheduled task for "Network Audit" but its disabled and not exactly sure what it is suppose to do.Any have more details on this?
Hi Guys,When I create a guest account and the account time expires, the account still remains on the WCS (but not on the controller).Is this a feature of the WCS or a bug?If so, can I ask the WCS to automatically remove all guest users accounts from ...
I have a small business about 20 PC's that I need to connect to a building that contains a group of computers on a sepearate network across a field, I would like to go wireless... I have a budget of inbetween $3000 & $4000. What equipment would you s...
Guys, Have received this message on my WLC.Is there a list of client exclusion codes that I can view with any guide to what I should do next?Client 'xx:xx:xx:xx:xx:xx' which was associated with AP 'xx:xx:xx:xx:xx:xx', interface '0' is excluded. The r...
We are using Cisco 1242 APs to do short building-to-building bridge shots using 802.11a frequencies. Is there a Cisco-recommended maximum RSSI or SNR value for such a link? I have heard from various link installers that too hot a signal can burn out ...
