Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

What am I doing wrong? I have configured a blank 857w with the config described here:http://www.cisco.com/en/US/docs/routers/access/800/850/software/configuration/guide/wireless.htmlHowever I get an error when I no shut the Dot11Radio0 interface conf...

I am trying to update our Smartnet for our location appliance but can't get the serial number. It's supposedly printed on the bottom of the device or accessible via WCS 'Advanced Parameters' page. The appliance is mounted in a rack not easily moved a...

us10610 by • Level 3
  • 560 Views
  • 1 replies
  • 0 Helpful votes

Having issues with a cisco 2950 switch that is feeding off of a lwapp 1242. The 1242 is connected through mesh to a 1510, I can connect to the 1242 throgh wireless and it works fine. I plug the switch or even plug the laptop directly into the 1242 an...

brock0150 by • Level 2
  • 582 Views
  • 1 replies
  • 0 Helpful votes

I have a set of bridges working right now on 1 vlan..which is the mgmt vlan I believe. What I need to do is add 4 more vlans plus a management vlan to this link for student registration(reg,quarentene,no -access and fullaccess vlans). The SSID I have...

jfergle by • Visitor
  • 817 Views
  • 1 replies
  • 0 Helpful votes

I am looking for a Linksys Access Point which supports follwoing features802.11 a/gSNMP support Vlan SupportYour promt reply is highly appreciatedcheers

mansoor9349 by • Community Member
  • 803 Views
  • 1 replies
  • 0 Helpful votes

Hi Guys,This is a little bit of an odd request however I need to allow a sync routing due to some legacy routing to pass through my ASA.I have allowed IP any any between the particular hosts involved to allow for high ports etc.. However the ASA is t...

Will I be able to centrally manage a deployment of 9 Ap's with justa WLC and no WCS ? Im not sure how much management capabilities comes with the WLC interface. Can some one tell me ?

garbis by • Community Member
  • 512 Views
  • 1 replies
  • 0 Helpful votes

am looking for a Linksys Access Point which supports follwoing features 802.11 a/g SNMP support Vlan Support Your promt reply is highly appreciated cheers

mansoor9349 by • Community Member
  • 1159 Views
  • 3 replies
  • 0 Helpful votes

Hi guys,I'm tying to test the uAPSD with Cisco 1130AG AP and intel 4965AGN PCI, reading 802.11e standard I found that a SP has to be opened and client device has to send a trigger enabled flag. I'm not finding anything like that in my traces. Are the...

joshuasanz by • Community Member
  • 1208 Views
  • 0 replies
  • 0 Helpful votes

Hello everyone. I'm in the process of testing a new network environment that replaces all of my existing L2 trunks with L3 routed links. I plan to use L3 routed links all the way to the access layer. My existing environment consists of a variety of C...

dbroder by • Level 2
  • 1472 Views
  • 6 replies
  • 0 Helpful votes

Hello, we currently have several client sites(about 50), using Aironet 1100's. We are using WEP, and everyone is authing to our ACS. Would like to change everything over to WPA. What kind of issues could I expect...the clients connecting are constant...

shane.wesley by • Community Member
  • 1337 Views
  • 4 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card