Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi,Is there a way i can bridge a wireless and a cable vlan? Client requirements are that wireless and cable users will be in the same subnet. I am running a C1812W router. Configuration examples in cisco.com only include wireless vlans.Thanks./George...
Resolved! Yagi Mounting Direction
Next week, I'm going to setup a wireless bridge using 1310's with Yagi's at both ends. My question is, which direction do I mount the Yagi's? In other words, should the antenna's be pointed at each other? How does the signal radiate from the antenna...
Are there a set of best practices that one could use for deployment of Cisco APs or any general AP?Let me know.Thanks,Ohamien
Hi,I've 2 units of WLSE, performing redundancy, and 2 WDS configured.In the WDS, at the WNM config, I've enter the virtual IP of the WLSE, but it give a message of "NOT AUTHENTICATED"..May I know why is that??Thanks.
I spend hours trying to upgrade firmware on AIR-AP1231G-A-K9 to c1200-k9w7-tar.123-8.JA.tar . Http connection prompts me for login/passowrd, but never takes that password. Both telnet and direct console connections take that password, but would not u...
We've recently deployed about 150 1200's that are authenticating MAC address against Freeradius. The APs appear to be pounding the auth server with requests, so much so that the server is bogging down in other duties. A CCIE referred me to "Cisco IOS...
Hello,I am running a WLC 2006 with a couple of test LWAPs. I have everything running fine except for a Spectrum24 Client Bridge from Symbol. It is using an LA4121 card also from Symbol. Before you guys here flame me it cannot apparently use a Cisc...
Hi all,is over there any possibility to monitor coverage of signal antenas of AP. I know that exist site surveyutility.But what Im interested is somethingwhere I import map of our bilding (ground plan) and I will see range of AP?BRjl
I just reconfigured one AP to be the WDS infrastructure device, now WLSE tells me it's SNMP unreachable. I copied the config from the backup WDS which is fine SNMP wise. I can get the SNMP table with the WLSE, discovery works fine, but WLSE still rep...
Hi,I converted IOS to LWAPP-based AP using 1200 Series 802.11g radio module. My customer accidently deleted the only LWAPP software inside the flash.Is there a way to upload an IOS image into the flash? I tried using tftp but the following error occu...
Try to use WPA-PSK combinded with MAC filtering on Aironet 1231G (12.3(7)JA), but when i try to sett open authenticaton with mac filtering the WPA-PSK key disappear. Cant this be done?
I am in the process of relacing my Cisco 350 aironet with 1310 Aironet and would like to do a link test on the 1310 aironets. This gives me an indication on the signal strenght to and from the station.I know were to find the test from the 350 series ...
what will be the recomended authentication method for the workgroup bridges/bridges with the existance of an ACS ??i know EAP-FAST cannot be used, but will LEAP/WPA be the most secured??
Hi Wireless Lan controller 4400 the documnetation on this product is awfull . I am trying to configure wpa-2 using 802.1x authentication or leap is this possable as for web interface cannot find were you set authentication type. if wpa-2 uses a parti...
I am using Cisco Wireless Controller 4112. My question is what would be the scenario for using LWAPP layer 3 instead of layer 2?I want to have different VLANS be assigned to the user based on SSID the users have configured. Do I need to use LWAPP a...
