Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
hi all,I could not get the WLC 2006 to communicate with the AP1010. My configuration is straight forward. WLC2006----CE500----AP1010DHCP Server (192.0.2.222) also connected to the CE500. The DHCP server can ping the WLC2006 and likewise.configuration...
I selected 3 AP1231s running 12.3(2)JA to do a AP Radio Scan;Job shows ended one hour ago, but the radio data is still old. Site Survey Wizard - AP Radio Scan 3154 12:43:56 12/29/2005 No Yes - 12:43:56 12/29/2005 12:54:16 12/29/2005 jaarons The Job ...
I am thinking to setup a wireless network (Cisco Airespace controller 4100) using EAP-PEAP for authentication. We have a Microsoft 2003 server running IAS. My understanding is that a server side certificate is needed at the MS IAS server. I don't ...
Hi everybody.¿Where can I find an estimation of the coverage ranges that can be obtained with the AP 1200 and omnidirectional antennas of different gain?Thanks
Resolved! Cisco Aironet 1200 with poor/none signal
HiI have a Cisco Airnonet 1230B on the top of my building with a 9 DBI omni antenna, totaly isolated from the exterior, powerd with POE (about 50 meters long), and untill now everything went perfect, but yesterday the AP sudently went with no signal/...
We have 4 Cisco Aironet 1200 Series Access Points and they are all set to authenticate with our RADIUS server. However, one is hanging on authentication and we can't seem to figure out why. Does anyone have any knowledge/experience with configuring...
OK I walked into this huge warehouse and did not have the necessary tools to do the a site survey on such a space. I did get measurements though. So I am looking for insight as to what antennas i can use with the AP1200, and how many I might need for...
I was wondering if it was possible to manually set configs to default on these AP's(other than through the controller) or log into them via telnet or etc.....
Resolved! Further help for a 'Newbie'...
Hello again Folks,I posted here a few days ago (Pls help a 'Newbie', 27th November) and thanks to the prompt reply, I have now sucessfully configured my first Aironet 1200!I have another five to set up (for the same site) and I am now considering the...
Set up a wireless network using a 4124 Wireless Controller and AP1020 and AP1030 access points. The two AP1030's are at a remote office with a 6Mb pipe between the two offices. I am unable to associate the AP1030's to the controller. The AP1020's ...
The ISA2000 FW service will not start on the BBSM53 I have installed at a client premises.I had it working fine, issuing DHCP addresses, authenticating guests and allowing browsing and VPN traffic to the Internet.. the World was a good place....Then ...
Hi,I have a WLSE with 2.12 version firmware and AP 1210 serie with 12.3(7)JA firmware. I have several site location with 2 radius server (a main and a backup). When I turn off the main radius server, to make test, all the AP go to the backup to regis...
Hi,I would like to know if it is possible to pass trougth vlans on 2 1310 wireless bridges.I have a switch1 --> 1310 --> 1310 --> switch2. I want to pass vlans from switch1 to switch2.How can i do this?regardsLuís Rodrigues
Me again... I have an other issue...I'm trying to receive the mac-address for all theconnected clients to a Cisco access-point (Cisco1130) by SNMP.The best way to do this seems with the cDot11ClientConfigInfoTabletable.(CISCO-DOT11-ASSOCIATION-MIB OI...
Does the airespace WLAN with controller 4400 running software version 3.2.78.0, supports concurrent access on a SSID for WEP and WPA (migration mode)?
