Wireless

I have a vlan that has been defined on my core switch with the following configinterface Vlan50 description WLAN ip address xx.xx.xx.xx xx.xx.xx.xxon the controller, WLAN interface has been created referencing the above mentionedOn my core switch, i ...

I am trying to configure 2 new 1131AG's in the same manner as I have a bunch of 1200's configured for WPA-PSK, TKIP and open authentication using a local mac address list. The AP's are configured with a default native VLAN 1 for management and a VLAN...

Hi all. Heres hoping you can help........I hope you can grasp the following description of the test network I have. I admit a diagram would have been better but it's hard to send a whiteboard over the web : )I am currently in the process of designing...

We are about to migrate a site running Symbol AP4131 managed by a Symbol WS5000 to an all Cisco 1242 AP.I am trying to verify the APs will work together as we do the migration. Currently the Symbols are running a static WEP key. If I configure the Ci...

Hello,I need some idea with regards to our 1310 bridge. It was operational for more than a year and suddenly connectivity is lost. If in back to back mode, two bridges are ok. If connected at in actual distance (3km), no association is found.We have ...

I have one location that I'm having problems getting the laptops to associate to the 1130AG ap's. I'm using EAP-FAST w/ TKIP authenticating through a WLSM to ACS for AD authentication. When the laptop comes up it will initialize and then fail on asso...

Hi All,We have a WLAN setup with 1 AP 1230 assigned as a WDS, and the 16 APs configured as Infrastructure AP. Off late, I am experiencing a problem where all my clients are getting disconnected frequently. I have checked the logs and the logs indicat...

I have upgraded my 1200 AP to a 802.11b/g radio and now I am experiencing a lot of drops by my clients. When I was running just my 802.11b radio I had some issues with my clients, but after setting my channel to a particular one instead of "LEAST CON...

I am trying to switch from The internal ACS user database for password authentication to an ACE Key FOB server with the subject line config and I get Ext. Database Failed. It works for my routers w/ TACACS but not with the WiFi.EAP FAST <--> WLC <-->...

Hello,I have a question about configuration for external antenna. In the setting of Radio0-802.11g i can enable parameters for external antenna. I need to enter a value in dB: Antenna Gain(dB)?Which value can i put?I'm using AP 1231G with an external...

We're starting a wireless deployment with 1240 AP's and have run into a bit of a problem. It was decided that we label all of the AP's with the last 6 digits of their wireless MAC. Is there any way to find that information out of the box? I've consol...

Hi, I am have problem with Bridge and switch 3550, the port is Down and Up randomly.Anyone can help?.config is in the belowinterface FastEthernet0/23 switchport trunk encapsulation dot1q switchport mode dynamic desirable spanning-tree portfast.This a...

Hi,I am using Cisco ACS and Cisco AP AIR-AP1231G-A-K9. They are configured so that client can be authenticated using PEAP. However, as soon as join the AP to WDS. It stops working and no clients can now be authenticated by PEAP.000066: *Mar 1 00:52:2...

Hi All,My customer's environment is using WLAN Controller and some Cisco APs with ACS 3.3 using PEAP MSCHAPV2. They prefer to only allow the clients whose PC has logged in Windows Domain using Domain Account to associate the "PEAP enable" SSID.At pre...

I am trying to find out if I have setup my WISM and I have 802.1x setup within my infrastructure. And say I want to control which SSID a user is allowed to access via Radius Authentication. Is there away to send a reauth command to move a device from...