Wireless

I just read an interesting document about the Cisco WLSE, Air Magnet Enterprise, Air Defense. Since Cisco partnered with Air Defense and Air Magnet stating that they soon too will be able to intergrate with WLSE. Is Cisco leaning towards a new produc...

For hot standby,Should the mac-address of the active AP be the radio interface mac or the ethernet interface mac ?http://www.cisco.com/en/US/products/hw/wireless/ps430/products_installation_and_configuration_guide_chapter09186a0080147d79.html

Can I use the ap 1200 dual band for two diffrent role, 2.4 Ghz for in-building and 5 Ghz for inter-building; if so, the 1200 can be an access point and a bridge in the same time

Hi. I have a 1220 that I need to reset to factory. mostly because I dont know what its IP address settings are on it. I tried to console in but dont have control, I can see stuff scroll by but it isnt accepting my keyboard input.It stops when it gets...

My main concern now with 802.11 is deploying wirless into critical systems environments. Does anyone know the real risks of denial of service against 802.11b and g, and the effects of flodding a 2.4Ghz range? I ask this because I have a few custome...

Hi ,i have one cisco Aironet 350 using Channel one connected to an outdoor OMNI antenna( 12 dbi) Mounted on a tower of 20 meter height and providing connectivity to multiple remote sites , i am planning to add another Cisco Aironet 350 in the same...

Problem: When using the web GUI to manage an IOS access point such as the AP350, AP1100, or AP1200, and when using TACACS+ to authenticate the HTTP accesses, the access point will send numerous authentication requests to the TACACS+ server for each w...

i have a couple of cisco ap1100 aps running with cisco acs and wlse. when access points were running an older firmware, both b and g radios are able to connect and authenticate using the windows peap client. after firmware upgrade to anything later t...

Hello! I have one AP tested on the wireless network using LEAP encryption with 802.1x authentication using CiscoSecure ACS. It is working great. I now have to extend my coverage to another floor and need to put a second AP. What is the role of the se...

I am trying to use the WLSE to configure a MOTD banner on all my APs. So I go to the custom commands window and enter in the text. I do not include "conf t" command. I tried it and the config job fails. When I remove the "conf t" command and run ...

Hi, has anyone got some good documentation on setting up EAP-TLS with windows 2003 Active Directory/CA, IAS and Cisco AP1200.Cisco ACS 3.3 does not support NTLMv2 so I have to use IAS.Any suggestions?

Does anyone have any information about the acceptable CISCO parameters for an AP1200? We see high buffer misses and discards yet no degraded performance. We have set standard defaults on these parameters but need to know what CISCO deems correct va...

I've tested Association ACLs in 12.3(2)JA and JA2 and they are not working. They work fine in 12.2(15)JA and earlier releases. Has anyone else had this problem?

I have 1100APs & 1210APs running 12.2.15XR2 & one test AP (1100) with 12.3.2JA2. With certain client adapters; namely Netgear WG121 (USB), Netgear WG511 (PCMCIA), and Linksys WUSB54G (USB); I cannot associate to my APs. The Funk Odyssey supplicant s...

HiWe have three building networks (A,B and C). They are very far. The customer needs to use wireless bridges to link them up.They bought four 350Bridges. One 350 is placed inside each building, and the fourth one is at the central.The networks at at ...