Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
I try to upgrade a WS-SVC-WISM-1-K9 from 3.2.116.21 to 4.0.155.0 (SWISMK9-4-0-155-0.aes)which fail with this error:Tue Jun 13 14:36:41 2006: tftp rc=0, pHost=1.2.3.4 pFilename=wifi/SWISMK9-4-0-155-0.aes pLocalFilename=/mnt/download/local.tgzTue Jun 1...
We have a number of AP350s which we're upgrading from VxWorks to IOS. The conversion to IOS works fine but when I try and upgrade to a later version of IOS frequently the dot11radio0 interface disappears after the upgrade. On one AP the interface cam...
I have two root bridges - A & B - and I have one non root bridge - Z. The bridges A & B are broadcasting the same SSIDs and so Z can associate to either of them. The directional antennas, line of sight and everything has been set so that Z would obvi...
If I currently have an 802.11g network that has been optimized to support data devices at 36 Mb/s or higher (i.e., AP cells a little closer to maintain higher speeds) and I now want to add 7920 wireless phone support, do I have to re-do my site surve...
I am not sure if this is the correct place to ask the following questions, but here it goes...As part of a wireless pilot project we have installed 50 access points (Cisco aironet 1231G) in a couple of buildings. The real project once approved could ...
I am setting a wireless interconnection. In the Head Office I have a Cisco 1310 root Bridge and in the remote office I have the Cisco 1310 acting as the bridge. My question is - Could I directly connect the Cisco Access Point to the Cisco Aironet Pow...
Hi,We have to implement wireless lan with WRT5RG devices.We have the reason to use only this model.Our question is how much area one accesspoint can cover. Based on that we will decide how many access points we have to purchase?Regardsskrao
AP boots fine on ac power but drops power entirely upon connecting ethernet cable.
I have an aironet 1100 configured as the root and I want the aironet 350 as the repeater. After all is setup I keep receiving authentication failed messages on the log of the 1100. any thoughts?
Hi All,I have got Aironet 1210 and want to implement MAC Authentication without ACS.Now, I know that any Aironet AP can allow MAC-Authentication by itself storing all the MAC Address List.Hence after the command:TestAP(config-if-ssid)#authentication ...
I have setup a lwapp system with about 6 AP's. Everything works great but on one of the WLAN's I have Web Authentication setup. For some reason, I cannot get this to work. I have tried every setting possible, played with the virtual interface but I c...
I tested windows XP SP2 client PEAP machine authentication with ACS server. The ACS uses self signed certificate. I have to uncheck "Validate server certificate", otherwise machine authenticaion does not work even I have imported the ACS self signed ...
When do you enable the ethernet multicast mode on controller? In my test lab, I have it disabled and I have not seen any issues so far. Thanks.
At the informational link below - we are informed that when using LAN interfaces for failover link you must go through a switch and not use a cross-over cable between the two pixes in the pair. It does not however explain why this is the case. Does a...
I have 3 BR1310 units, all on 12.3(8)JA2, and set to use WPA-PSK. One unit will be located outside a main building and acts as the Root. The second unit will be located on a small hill and act as the Repeater. The third unit will be located at a remo...
