We have currently purchased a test laptop with the new intel 2100 card that "supports LEAP" Intel Is telling me that drivers must be obtained from Cisco. I have tried teh ACU which obviously does not work being it is not an aironet card. Anyone t...
We have currently purchased a test laptop with the new intel 2100 card that "supports LEAP" Intel Is telling me that drivers must be obtained from Cisco. I have tried teh ACU which obviously does not work being it is not an aironet card. Anyone t...
I have several access points in one location. I set the maximum number of associations for my wireless voice VLAN to 5. After 5 associations, the 1200 will not take more....that's what I want to insure quality.But, how can I force a phone to skip t...
I want to use wireless to bridge a long distance in my plant instead of using fiber. Can I use a 1200 AP to do this or do I need a 1400?Thanks!
Is there an approved amplifier for the Aironet 1200 ?My current setup is as followsAironet 1200 @ 100mW30ft of LMR 40015 dbi omni AntennaI want to extend my PCMCIA roaming range to a diameter of 1000ft and am having no luck... can you help me?Thanks
After upgrading th AP1200 to IOS with the conversion image the unit fails to start, when conencting a terminal to the consoleport you got this message:Testing DRAM...(press <esc> to bypass)DRAM OKPower-on reset.Copyright 1996-2000 Cisco Systems, Inc....
What are acceptable values for the "Carrier Busy" and "Noise Value" when performing the carrier test on a 350 bridge?For Carrier Busy, I'm getting 10% max across all channelsFor Noise Value, I'm getting -83dBm max across all channels
I have 1200 series access points running VxWorks 12.03T. I have the LAN version of Ciscoworks2000 (assume latest version). The ANI server in Ciscoworks discovers the APs but doesn't recognize them (they show up as unknown). Can the LAN version of ...
I am having a problem pinging any wireless clients. They associate, DHCP fine and can access hosts on the wired side. However, from the router or any wired device in the same vlan as the wireless device, I get no replies from the ping. This had wo...
Is it possible to map an SSID with a Group on the Tacacs server ?I've differents SSID (and VLAN) on my AP1200 with MAC-address authentication, and I would like to authorized a MAC only for thi SSID with a ACS group.SSID "A" with MAC "A"SSID "B" with ...
what is the best way for a wireless survey for 7920 ip phone?i have a Wlan with 3 AP350 and 3 AP1100, and 10 7920phone.i have many doubts about the "roaming" ....thanks
I will have to design a wlan for a supermarket. Any idea if I can design a wireless lan without using a hub or switch?
Does anyone know why when you log in to your device when you are using the new ACU it takes about 60-70 seconds for the splash screen that says "starting LEAP-> Checking Link Status-> Renewing IP add-> Finding Domain Controller" to go away? It seems...
While roaming on 1200 AP's with multiple VLANS using cards and VOIP phones the VLAN will quit passing traffice after roaming between multiple access points. Any answers
We are using PEAP authentication with ACS 3.2, wink2 client with the Microsoft PEAP supplement (Q313664). When the client is booting up it associates to the AP and the AP initiates the EAP process. Because the client is still in the boot process an...
Good Morning,Our 1100ap is setup as a DHCP server. I've attempted to add an access-list to f0 that blocks bootpc and bootps requests from coming on that interface so that addresses will only be assigned on requests coming in on the Dot11Radio0 interf...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-27-2025 06:05 AM | ||
02-18-2025 11:22 AM | ||
02-13-2025 10:43 PM | ||
02-13-2025 08:57 PM | ||
02-04-2025 03:06 AM |
User | Count |
---|---|
12 | |
10 | |
5 | |
3 | |
2 |