Wireless

halloI have some doubts about how QoS works in wireless bridge AIR-BR350.Are the following sentencies correct ?1) there is only Priority Queueing from radio-to-Lan direction.2) I can give priority only to certain traffic from radio-to-Lan.3) I can mo...

halloI saw that I can configure different IP addresses on LAN and Radio interfaces of the AIR-BR350 wireless bridge.I can configure a routing -table too.Do these features mean that AIR-BR350 can work as a router or must I use a cisco-router (eg. cisc...

Has any of you guys experienced deploying Cisco's PDSN and Home Agent for EV-DO? How is it faring?Can you give me some design guidelines for this Packet Data System portion of the EV-DO technology.ThanksFrancis

Hi,I tried setting up encryption between two 340 bridges running versions BR500E V8.80 on one end and BR500E V8.65 on the other, when I activated encryption on, it brought down the connection, then I had to remove encryption on the other end to get t...

I have a 350 access point that displays itself as a 340 access point. I have performed an upgrade to 12.03T. During bootup a HyperTerm session lists the FLASH as containing a 340 series Firmware 05.2ou. This device fails during the conversion from ...

What's difference Virtual-Dot11Radio0 and Dot11Radio0 and BVI?and what's "Interface Virtual-Dot11Radio0, changed state to Down","Interface Dot11Radio0, changed state to Down" mean?

Can anyone tell me when this is going to happen? Currenty supports 802.11b, but I am about to install a whole load of .a radios and was dismayed to see that the site survey etc. won't work with .a. Cisco moderator any ideas? Anyone else?Muchly tha...

Hello,I have a wlan composed of AP 1100 and tkip with cmic is configured. I want to configure SNMP to manage the aps remotly but i heard that the wep key can appear in clear. Firstly is it true and what can i do to correct this if i want to use snmp....

I have a large existing install base of 802.11b AP's and clients (data only). Throughput for many areas is becoming an issue. A purchase has been made for 802.11g AP’s and clients to support users requiring higher bandwidth, however I not sure this...

I am trying something new and cannot get a particular configuration to work.I have a yagi antenna connected to an Aironet 350 Bridge set as Non-Root w/Clients pointing to an 2.2 dbi Omni antenna connected to an Aironet 350 AP.Both systems are running...

Hello, I have an AP-350 that upon applying power remains with the 3 led of color orange (static) and with the following menu (seen by hyperterminal) :c -- Copy filef -- File dirl -- downLoad file into DRAMu -- Upload filep -- xfer Protocoln -- coNsol...

I was thinking about upgrading our seven AP1200s to the ISO software. Is there a real compelling reason to do so? I've read a lot of problems doing so in this forum and would like to know the benefits. I'm very new to Cisco products and would like to...

I am trying to authenticate my users with radius using a windows 2000 server with Radius (IAS service), configured all parameters in AP and ACU and seem everything on server, AP and client are correct. Is there compatibility between Windows Radius an...

Dear ColleguesPerhaps you can help me out on this: I am connecting the units above, the 1200 on a Server 2000 network and the WGB on a peerless Win 98/XP network. The units will communicate with each other from their web based setup menus but not fro...

Hi, I want to restrict access to the management port ie. BVI1 using an ACL. I can't see a way to do it using the HTTP GUI so I want to do it using the CLI. My question is....are there ramifications of using the CLI instead of the GUI or vice versa...