Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I can't update the firmware on a AIR-AP1230A-A-K9 wireless acces point via http (or tftp). It reports "error:the software upgrade was interrupted and was not able to be completed". The file I'm trying to use is c1200-k9w7-tar.123-7.JA1.tar and curren...
Can anyone enlighten me on this question.When using Power injector to power up the AP, what will happen to the person if he were to cut the ethernet cable when there is power being transmit over the cable?
The WLSE uses the account [email protected], so our smtp server rejects all sending mail attemps. How can I change it to casuser@domain for the smtp server to permit it?
I get the following errors on all of the Wireless LAN controllers I have configured:Thu Oct 27 14:08:41 2005 [ERROR] dhcp_proxy.c 2897: Received a packet from ourselves, network loop! Thu Oct 27 14:08:26 2005 [ERROR] dhcp_support.c 357: dhcp_bind(): ...
I'm putting together a design and want to know if it is possible to use two AP1200s as bridges with the non-root bridge being mobile and allowing client connections whilst not connected to the root bridge. Secondly can I set up leap authentication us...
I have completed a site survey using the Aironet AP 350. I am now considering implementing the Airspace 1000 AP and their switch solution. Can the survey results be used with some degree of confidence to determine number and placement of these new AP...
Hiwe get alerts when there are rouge aps or ad hoc neterks. Problem is when the ssid is not broadcasted, in the wlse there is just /x/X os something like that instead of a ssid.when i get an email from the wlse and the ssid is seen then its correct:S...
Hello everyone,Over the past few months, I have installed several WLAN's using Cisco YAGI antennas. They seem to be a nice piece of kit to work with. Although, because they are fairly directional. Most of my install time is spent lining them up corre...
In my wireless deployment I am deploying 1010 series access points and 2006 wireless LAN controller. My question is: How will my wireless clients get an IP address if my AP's are in different subnets than my Controller and I don't have a DHCP server ...
I Have WLSE v. 2.11 and there is a problem with authentication between WLSE and WDS access points. I am using Cisco secure ACS v.3,3 and the infrastructure AP´s are being authenticated but the WLSE can´t authenticate with WDS and it´s impossible obta...
Now that the PCM352 has been end of lifed, to go from a PCM352 series client card to the one of the new CB21AG client cards, will we have to un-install the 352 driver software then install the CB21 card software?Thanks
Hi Everyone,My understanding of a general PIX config is to have the inside interface connected to your LAN and the outside interface connected to the "Internet". Now I have configured the NAT to translate my internat 192.168.x.x address to my routabl...
When I highlight one of my APs in Device Center, it says it is connected to one of my other APs on FastEthernet0.I have several aps but only these two aps show this message that they are connected to one another through FE0.Can anyone explain why thi...
I'm curious how I can authenticate my 1300 bridges as a client to a WLSE Express.. The WLSE Express does have a built in AAA server and i've created the usernames, but, i'm not sure where in the 1300 I can assign it to authenticate to the WLSE.. My q...
Hi I need some help. Has any one used "MSI RG54G3 54G Broadband Router with 4Port switch + 1xWAN NAT/Firewall/VPN" box ? If yes how is your experience ?Can any one recommend a good and economical wireless box for home lab ?Thanks
