Wireless

I am Instaling AP and I don't know which ports should be opened on switch for communication between Access Point and CiscoWork. For now we open all ports to CiscoWorks station, but we want to cut it as much as its possible. Also we've got problems wi...

hi,i have cisco aironet & cisco secure ACS.what do i need to implement captive portal ?basically what we want is some sort of authentication when a user start to browse.thank you

Hi guys,In our office we have a Cisco Linksys Access Point which is connected to a Netgear switch then to a Cisco 877w ADSL router. | ||________| ________ ___________ |Link Sys|<------------>|NetGear |<------>|Cisco ADSL ||Acces pt| |Switch | |Router...

Hey guys,I need some clarification. Is WDS mandatory for WLSE??I have a client with 120+ AP's and they are using WEP (ugh, i know) between their phones and the AP's. Can I take two of these AP's and configure them as WDS?? If so, what do I need to do...

I have created a new SSID with Open + MAC auth to an ACS server and a new VLAN on an AIR-AP1231G-A-K9 AP running 12.3(7)JA2. The WEP key negotiates on the client just fine, but the AP shows that the client MAC auth fails. The ACS server shows no fail...

I am having problems getting my new wireless card to work in my 1841 rtr. Attached is the current config and the docs I have used already to try to get this working. I have looked at the 1800 config (fixed) doc and others. If any one has any ideas or...

Hi all,I have very basic question related toroaming of WiFi clients between twoAPs. Should I configure both with the same configuration and roaming is done automatically? Or, should I do anythingmore. I set both to Access point root.BRjl

I have a Cisco AP352E2R that appears dead; When powered on, the Ethernet light stays on red, Association status stays on Green, and the Radio Activity stays on Orange. The first time I plug it in, my USB Serial adapter shows no activity. If I unplug ...

Hi guys...In our office we have a Cisco Linksys Access Point. At a time a max of 5 will be connected. We do the MAC authentication. Every day when i start my work i am finding a great trouble for getting connected to network. It takes atleast 15-20 m...

I have two WLC4404-100 controllers where I just installed the secondary unit. I have edited certain APs to make the primary controller be this new unit and the current controller to be the secondary. These APs do not move unless I reset them. These A...

I configured wlse (2.12) to send e-mail notifications to my address, but i don't received anyone and then i run "show maillog" and this is the result :Dec 28 15:26:28 wlse sendmail[6444]: jBSFQSm06441: [email protected], ctladdr=casuser (200/200), ...

I have two 1131AG’s (12.3(7)JA1) in my environment that I am currently using WPA-PSK for encryption. I am using the same 63 character PSK on both AP’s. I am running multiple VLAN’s through both access points.My scenario:I take my laptop, select which...

Hello, I can't view 2006 wireless clients reports in the Cisco Works Wireless LAN Solution Engine. I can only select years from 2002 to 2005.Is it a bug? or am I the only one with this problem?I have installed the last firmware 2.12Thanks

HelloHow can i configure the wlan on cisco 1812w?I have a VLAN with connection to WAN.This VLAN have an DHCP.If i connect with RJ45 all its ok (DHCP and connection to outside). Ping to the gateway it´s okBut if i try to connect from WLAN the DHCP its...

Hi All,This is a little simple for those who have faced the problem but a little lengthy for those who have not come accross the same. Please grab a coffee before we begin.Scenario: Am trying to have EAP authentication for my wireless users to be aut...