Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! Cisco AIR-AP2802I-E-K9 Boot loop Issue
Hello im have this issue where it completely boot looping every time. I've boot into part2 and boot fine connects to my other 2802I which is setup up as WLC. Then begins to download the image from my tftp after this is done reboots and get stuck in t...
Hi Folks, We just bought a Cisco Wireless Controller 9800 and Access point 9166l-AAm trying to join the access point to controller but it is not joining.I can see the blinking Red and Green light on access pointWhen i am checking the logs on Controll...
On a specific Floor we have numerous 9120 AP's and 1 x AP in particular is showing 95% of its clients with very low data rates of under 69Mbps. The AP is automatically setup to adjust its power rating and currently its level is 1/8 ( 23dbm ) which i...
Hi All,I am having an issue where on my SG300 with POE+ it doesn't seem like its giving full POE power to my Cisco AP3702. If I look on the WLC 2504 there is no text box showing POE statistics like I would see if I connected the AP directly to the co...
Not able to add 3800 with mobility express & 9115 EWC in single network. Mobility express delete EWC config if I am connect 9115 ap in network.
Hello All,After Wifi 6 deployments, we have observed that few of our users are randomly getting disconnected. We ran a script and pushed it to the users device to get the logs.We got the below error-Event 4042- Capacity change on {e4c61a7a-894b-4de1-...
hi We have 4 floors of office , recently added a WLC to add extra APs . we have Rukus ap too .we have successfully configured Cisco APs and it all connected to gateway too and WLc (open Security )and APs got ips but our issue is when ever a client c...
can i convert AP 3700 in to mobility express by changing IOs
Hey all.I setup a Twilio account to send SMS authentication using the splash pages. This is all working very well.However, I can't seem to configure Twilio / Meraki to use an Alphanumeric Sender ID - this is part of the Twilio API.Anyone tested this?...
Resolved! MR76 antennas
Hello,I need to upgrade some external Mr74's around an industrial site. These are mounted high on the side of buildings to provide coverage into open yards (where material is stored) so people can do stock takes with hand scanners etc.I have had a wa...
Resolved! Authentication with Trusted Access
I am trying to find a way to satisfy the need to authenticate clients on to a Meraki Wi-Fi network using certificates, where the customer has specified that the Authentication must not require additional (CA/RADIUS/etc) servers.I proposed System Mana...
Resolved! WLC License issue
My WLC has 45 permanent licenses and all are in use. Also, I see that WLC has an evaluation license with 12 12-week expiry, with a 1500 RTU license. Evaluation license in Inactive and permanent license is active Now if I want to add one more AP, can ...
Resolved! NPS woes with EAP-TLS & PEAP-MS-CHAPv2
Hi All,Having some more woes with NPS and wondering if any of you have had this situation. We have a heap of old devices that are authenticating using PEAP-MSCHAPv2 and we are in the process of migrating them across to EAP-TLS. We need to keep both m...
Good Day, I did a factory re-set on above AP (more than 60 seconds) the AP is on the same subnet as a WLC however the AP does not join this WLC due to model / firmware mismatch. I am connect via Consol and getting a stream of debug - I cannot break t...
Hi Guys, Are the following possible for FlexConnect, 1. Single SSID broadcasting to multiple site locations with their own respective FlexConnect Group? For example, BR_A = FlexGroup_A and BR_B = FlexGroup_B and both of it is broadcasting single same...
