Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

I do not have a radius server and I'm try to get my WLSE to manage my wds ap (1200). I have local radius running on the wds and other ap's are registered to it, but not the WLSE. Is this possible? Or is it a problem the local radius works on ports 18...

edpbrennan by • Community Member
  • 1684 Views
  • 8 replies
  • 0 Helpful votes

I am trying to set up PEAP-MS-CHAP v2. I am using Windows 2003 with IAS, Cisco 340 AP with 12.03T, Cisco 350 Wireless Card, Windows XP SP1. After logging with wireless user account, it connects, authenticates, and associates with AP for about 5-7 sec...

apoulatov by • Frequent Visitor
  • 2707 Views
  • 13 replies
  • 0 Helpful votes

I thought I would share the solution we found.Enviornment,Mixed hardware clients, all WIFI compatible.Cisco 1231 AP'sCisco Secure ACS for windowsWPA with PEAP Problem,Clients utilizing WinXP SP2 and wireless zero conf were not able to connect to our ...

With 2 sites using two 1300 bridges as a wireless link between the 2 LANs, what is the best mode to put them in if I only want the wired traffic to pass....not other AP's or Clients?

m-carey by • Level 2
  • 595 Views
  • 1 replies
  • 0 Helpful votes

All,Can someone please explain the deauthentication reason below from my 1200 event logs:Reason: Previous authentication no longer valid.What causes this? I'm using non-Cisco clients - is there a specific inactivity time out that causes this?Thanks!

Hi,As per my understanding the 1200 Series Access points running IOS (12.2(15)XR) send the management traffic (RADIUS,Accouting NTP etc) un-tagged i.e. using VLAN 1.As per our current setup, we assign this un-tagged traffic to a different VLAN (by ch...

mnlatif by • Level 7
  • 731 Views
  • 4 replies
  • 0 Helpful votes

Can someone explain the difference between the cipher TKIP and the cipher TKIP w/ 128bit WEP? I thought you got a key when you selected TKIP...Thanks in advance.David Beaver

d.beaver by • Level 4
  • 925 Views
  • 3 replies
  • 0 Helpful votes

I live in Serbia and Montenegro where local regulations gives 100mW on 2.4GHz. Unfortunately, I am not able to set the power output to more than 50mW on 1200AP. Is there any possibility to "unlock" the radio and to use 100mW? Any answer is highly app...

suonline by • Community Member
  • 509 Views
  • 1 replies
  • 0 Helpful votes

Hello,I have problems deploying PEAP. I have ACS3.3 in Windows2000 Server; AP350; client Windows XP with PCMCIA 350. All is configured as it says in the docs.I am working with the ACS local database. Certificates and all the stuff is ok.I attach the ...

Goodmorning..I have a four bridge setup, two spearte SSID, with a cross over in the middle. ME*-rootA<--->non/rootA---rootB<--->non/rootB*ServerBI have a solid link over a ten mile area. Couldn't be happier with the peformance. Lan traffic does pass ...

lodoss24 by • Community Member
  • 513 Views
  • 1 replies
  • 0 Helpful votes

We have two Aironet 1310, connecting two office buildings. Association works fine, they get linked at 54MBit/s. But when we measure throughput, we get results between 8 and max. 15MBit/s.We can see CRC errors climbing up, but signal strenghts is quit...

jjjwinkler by • Community Member
  • 1198 Views
  • 3 replies
  • 0 Helpful votes

Dear Sir,I would like to auto generate a new session key every 30 minutes running LEAP using AP 1200 Local RADIUS authentication? How can I configure it? I noticed there is a session timeout option under Security-->Local RADIUS Server-->User Group, i...

c.ong by • Level 3
  • 730 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card