Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi,my AP'S are all in the latest ios version (15)is there a way to manage the policies for these optionin wlse wrote that is could be on Nonios http disabled:(Nonios)telnet disabled:(Nonios) etc... please help !!!
The config file below is guaranteed to work.I have an ACS 3.0 server doing the MAC Authentication. So you have to take the MAC address that you want to allow, throw the MAC in the user name and password fields in the ACS and just load the AP with con...
Is it possible to clear or erase the log files - ? Without erasing the config ?thx
HiSo I've got a W2k server running IAS/DHCP/Certificate Services. My wireless client is WindowsXp. I've got everything setup exactly as listed here;http://www.cs.umd.edu/~mvanopst/8021x/howto/My IAS/CertificateSrv/DHCP server has got a computer certi...
I am looking at possibly using Cisco 1300 series bridges for mobile vehicle use to connect to other 1300 Bridges on towers. I thought this might be a way to save some money over the more expendive and custom build 3200 wireless routers. The only issu...
Hello,We have AP1121G, working with PEAP-GTC authentication.The authentication proccess is working fine but we are unable to automatically get an IP address from the DHCP server, we have to perform an ipconfig/renew in order to have it.We try to conf...
I've looked on HP/Compaqs site for help with this and find nothing. Maybe someone here can help. We've gone from at Netgear ME102 to the Cisco 1200AP. All the machines in the company can see the new Cisco and get authenticated except for these 2 HP/C...
We have successfully configured an AP as WDS and registered infrastructue Access Points. The WLSE has also successfully been authenticated by the WDS AP. My problem is when I move the WLSE onto a different subnet it looses the connection. I understan...
Dear Sir,My symbol scanner cannot get connected to this access point. The AP has the following status which I managed to captured and did a comparison with another access point.Failed association to AP,Under AP radio:internal advanced, Requested Stat...
This site has 8 APs, they are all running default conf with the latest ios based sofware. its work fine to a certain degree. you can roam between them all fine, with all our PDA's. there is no WEP or anything else running to keep it simple. The PDA's...
How many frequencies are used in OFDM? And howdoes this modulation relate to Spread Spectrum.I mean what's the spreading factor gained withOFDM vs. DSSS? If there are only 2 carriers, canOFDM really be classified as "Spread Spectrum"?
We have put the Wireless LAN AP 340 in a different VLAN. The clients are able to connect and access the network even in different VLANs but cannot browse the network using the My Network Places -> Entire Network.Is there any way that WLAN clients can...
I have two 1310g bridges in a point to point configuration, one root and the other non-root. How do I measure the signal strength between them, I am looking for something like the ACU utility which shows signal strength from an AP to the laptop.Other...
Hi all,What is the command to use roaming layer 3 in ap1200.i've 2 different subnet. 1 ap which have 192.168.2.0 and the other 192.168.3.0what i want that the client from 192.168.3.0 can connect to 192.168.2.0 without disconnected.thank for ur help.
Hello everyone i have a cisco pix 506 directly attached to a cable modem, and a cisco 2621 attached to the other side leading it into the network<2950>--<2621>--|pix 506|--<Cable Modem>--<Internet>syslog attached with error detailsrouter config attac...
