Hello, i changed my wifi setup from Unifi to Cisco and make my first steps.In syslog i cab see many entries like the following messages%RRM-3-RRM_LOGMSG: rrmLrad.c:5634 RRM LOG: Failed to lookup data rate for encoding 35389926, with channel width 20 ...
Forum Posts
Hello there, I added an AP Group on a WLC Cisco 5508 but this AP Group does not appear in Prime 3.9.0.In Prime there is an issue "Wrong CLI Credentials" does this correspond to the missing synchronization mentioned above?Also the associated APs which...
I have AIR-CAP2802I-E-K9 AP and it was working fine, suddenly it was disassociated with WLC, I found its static IP configuration was washed out, I tried to prime it through console and on that time it was associated with controller, as i powered off ...
Dear all, anyone has any recommendation what are the requirements from Catalyst 9800 (IOS-XE 17.3.3) configuration point of view (Flex Profile, Policy profile,...) in case you have an AP which suppose to broadcast locally switched WLAN, however on lo...
WLC Cisco IOS XE Software, Version 17.06.01C9800 Software (C9800_IOSXE-K9), Version 17.6.1, RELEASE SOFTWARE (fc6)AP ver 17.6.1.13 My 1+5T phone (Snapdragon 835, Android 10, Security patch 2020.09) won't connect to SSID.I've tried configurations like...
Trying to convert 1572E from lightweight to autonomous but not working. Configured and IP in ethernet port and bvi interface. APac3a.6744.a720#ping 10.1.1.1Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds...
Greetings, The 9120 AP needs to have the CA certificate as trusted certificate so that it can connect to the RADIUS server and authenticate as Dot1x supplicant. Could you advise how to upload the CA certificate to the AP ?. The WLC is a 9800. Regard...
Hello community, I have an issue with cisco WLC 9800, for wireless users I have 50 vlans, the issue is that when I want to create a Flexprofile it's only support 16 Vlans, there's any solution for this issue. Wireless LAN Controller
Hi really hope that someone can help me. I have a WLC running 8.5.171.0 and it has 3 x LWAPP 2602's connected to it. All three are seen and connected to the WLC. 2 are in one location and 1 in another. All three have their correct IP's, and I can...
Resolved! Stable 9800 WLC Release
What is the stable 9800 WLC Release ?TAC recommended 17.3.4 with APSPs and SMUs causes 9130 APs crashing 20 times a day.
Hi Please see the below session of cisco document and its link. What vlan does the AAA server provide with highlighted "VLAN provided by the AAA server"? The vlan is referring to the same vlan that is configured as native vlan at the switch port? Tha...
Hi For local authentication with Flexconnect, is there any difference between authentication at the AP and at local radius server? Thank you.
Resolved! cisco AP wIPS monitor mode
Hello Engineers, I was wondering about WIPS function, so I am searching about this.I found that I can setup the current AP I have to become a WIPS monitor mode on WLC. This configuration is not familiar with me, so I'm worried about license issue. A...
Resolved! AP NOT JOINING WLC
Dear community, I have an AP 1542 outdoor and wlc 3504. The Ap can't join the controller. I keep on getting this error. On the GUI i see radius authorization of the ap has failed. But no Ap policies is enabled! [*10/22/2021 14:09:42.0499] GOING BAC...
Hi guys,We have a customer with 2600, 2700, 2800 APs and we're migrating a customer to 9115, 9120 and 9130.They have a pair of 5520 running 8.10.142The customer's switch ports are configured with dot1x and mab authentication. The ports are configured...
