Wireless

I tring to get the card to come up during bootup. The linksys works this way, but Cisco cards wait for the user to logon before activating the card.

The CB21AG card ships with Aironet Desktop Utility (ADU) - does this software currently have similar software tools as Cisco's ACU. To be specific, does it have a "Site Survey Utility" and/or "Link Status Meter"? If not now, when will we see these fe...

With the ACU installed, I was able to get PEAP working on my 350 card and my 1100 AP. Without the ACU, I just can't get it to work. I the Dynamic VLAN assignment works ok, but I can't get an IP address or pass traffic with a static IP. Has anyone got...

Hello.I've just found these forums and I must say how good it is to find such a good source of information. I'm having a little problem with setting up a Home Wireless LAN and I would appreciate some help. I recently bought a AP350 from eBay and I'm ...

I am trying to get the DHCP server on the AP 1100 working, my question is: Can i also push out a Gateway IP and a DNS server ip with the pool that i can create on the AP?? Do I have to do all of this through IOS or is there a way to do it through the...

I suspect my problem is one due to some trees growing taller this spring and such but I figured I would post a message here to see if anyone had any other ideas.I have two BR350's about 2 miles apart using a Cisco Parabolic dish... the bridges have w...

I have a Cisco 4506 linked to 3 3550 switches. The 3550s run 14 Cisco 1200 APs. The mobile devices are Symbol RF barcode scanners. On the 4506, I get log messages like this:May 31 11:17:03: %C4K_EBM-4-HOSTFLAPPING: Host 00:A0:F8:61:0F:EA in vlan 28 i...

I am using a VPN3005 to secure wireless traffic.Using the public interface for the wireless traffic, I can pass DHCP through to get a wireless address and create the VPN tunnel and use 3DES encryption.My problem is that on the 3005, the default route...

HiCould anyone point me towards a good doc on how to configure an AP1100 to do EAP-TLS auth. using Windows Server 2003 as the Certificate Server and using Windows IAS 2003 as the RADIUS backend? I've found a doc "EAP-TLS Deployment Guide...." but it ...

halloI setup an aironet BR350 with web interface to make some tests, and I setup an account for administrationuser=adminpassword=nimdaNow I want to reset all config to factory defaults to cancel all passwords ...I used the procedure described in Soft...

I am implementing a ACS 1111 Cisco Secure ACS Appliance and am trying to find the agents that are needed for the windows workstations to authenticate thru it. I cannot find anything that isn't 3 years old and only for 95/NT. I know there's got to be ...

The call came to me that the bridges were not talking anymore. I reload the configs but this didn't resolve the issue. The 340s are running 8.80 and the one 350 is running 12.04. This setup has been working for several months. The two Aironet 340 Bri...

Hello,I am looking for the simplest configuration on an AP without any vlan or sub-interfaces configuration. Really the basic configuration for an AP with :- 1 IP adresse- 1 Netmask- 1 Default GatewayThx for any help.

I just did a test in the lab where I have WDS configured between APs. My client (SSID) and AP are configured for LEAP and WPA key management. I noticed that even though the client (SSID) is configured for WPA (not CCKM), it was still getting authenti...

Hello,We are trying to enable multicast/video streaming on wireless equipment AP1200.There are a known Bug CSCec72147 : When multicast streams over 300kbps are sent over the Dot11Radio interface, packets are dropped causing poor quality in the multic...