Hello,I have a problem and cannot access to the dhcp server when i configure wep encryption . Do i have miss something with wep configuration? ThanksRegardsBeatrice
Hello,I have a problem and cannot access to the dhcp server when i configure wep encryption . Do i have miss something with wep configuration? ThanksRegardsBeatrice
We received our 7920 phones yesterday! They work very well except for the fact that the services don't come up. No corporate directory or other services I have comfigured for 7960 phones. I am running ccm 3.2.2(c)spH. I have looked around cco, but I ...
Hay GuysAnyone know how to reset password for aironet BR100E ? Please help meThanksThomasNB: There is no hole or button for reset on the BR100E.
Besides what is in the IOS configuration guide, are there any WDS design docs yet?If you have multiple VLANs doing LEAP, how do you choose what VLAN WDS will run on? does it matter?Would a good solution be to run LEAP on the Native VLAN and run it th...
HiDoes anybody know if any USB WLAN client device support peap with cisco aps? Which usb client adapter does peap support? Does linksys WUSB12 support peap? i dont find usefull infos about peap with usb adapters.we need and usb device, cisco doesnt h...
HiI have a short question about leap config and broadcastkey roation.What do i really need. if i use tkip and mic i dont really need to configure boradcast key roation am i right?When i configure bc key rot. i set an interval with i also set on the a...
When using an AP1200 do I need to install one or two standard dipole antenna (2dBi)?Thank you!Rouven
I have two br342 worked in bridge mode, and connected two LAN together( there are two br342 with firmware version 8.80 and two yagi 1949 antnna, the distance is about 1.5 Km). Formerly they all worked fine enen in bad weather.But recently the two bri...
I am running Ciscoworks2000 and trying to get my Access Point's to send messages to the RME. I have enabled SNMP and created user's with the correct SNMP strings? Any help in getting as much information from the AP's to Ciscoworks would be greatly ap...
I'm trying to set up a configuration were administration access authorisation is granted by a ACS server (ACS v3.2), but cannot get it to work.In the AP1200 [12.2(11)JA] I've set up:- Administrator Authenticated by Authentication Server Only- a serve...
We have a client who wants to connect to his companies VPN Server. However he is unable to get a connection, just says it's refused. Each client is connected via a SmartBridges AirBridge to the local Cisco Aironet 1220 Series AP. Each client has a pu...
Im trying to configure a Cisco AP340 ver.11.07 authenticating users using EAP protocol onto our ACS ver 3.0 to a W2K domain external database. I had checked all the points mention in the documentation that can be applied to my case. I can ping the A...
I am looking to test PEAP, and I wanted to know if there is any documentation out there on how to set up from scratch, not only on the APs, Cisco's ACS, but on a Windows 2000 server as well. We have not implemented Active Directory, so I assume the C...
For CAR AAA service properties, "Type" is one of the required field that need to be filled.The options either to use eap-leap, eap-md5, eap-sim, file, group, ldap, local, odbc, radius,radius-session, rex, or tacacs-udp.Question:1. If CAR need to be i...
Attempting to setup wireless users to authenticate through new ACS 3.1 server. With our test user we are getting an error message in the 'Failed Attempts Log' that we can't find and explanation for to see what it means. In the Authentication Failure ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-16-2026 05:39 AM | ||
| 11-12-2026 01:01 AM | ||
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |